Combi 8045 instruction manual Green, Striped Zone

Page 13

8

9

10

11

12

23

Place base rear-facing in the vehicle seat location selected with blue lap belt guides toward vehicle seat back and centered between the vehicle lower anchors (fig. d).

Attach car seat to base.

Adjust recline using recline indicator on the side of the car seat. Line of recline indicator MUST be in green striped zone (fig. e). If line is not in green striped zone, adjust base using recline foot (see “Base Adjustment” section), and recheck recline of car seat. Repeat until recline indicator is in green striped zone.

If base can not be adjusted to locate the line in the green striped zone:

1.If necessary, place tightly rolled towel, pool noodle, or firm object under recline foot to level car seat.

2.Try a different seating position.

3.Do not use this infant car seat.

NOTE: Vehicle must be parked on horizontal surface

during this installation.

 

 

Green

Remove car seat from base.

Striped Zone

Connect lower anchor connectors to vehicle lower anchors:

-With hook-on connector opening facing down 1 , position the opening of the connector over the vehicle lower anchorage. Push down 2 and then pull out 3 on the connector to lock it onto the vehicle anchorage (fig. f). You should hear a click.

-Pull on connector to be sure it is locked onto the anchorage.

-Repeat for connector on opposite side.

Tighten lower anchorage belt to secure the base. Press down in center of base to depress the vehicle cushion and pull free end of lower anchor belt to tighten belt around base (fig. g).

Check for secure installation. Pull base front to back and left to right to check for secure installation (fig. h). LATCH belt MUST stay tight.

If LATCH belt does not stay tight or base can not be securely installed, try a different LATCH location or use the vehicle’s seat belt to secure the base.

(fig. g)

24

(fig. d)

(fig. e)

Recline

Indicator

1

2

3

(fig. f)

(fig. h)

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Combi Connection Infant Car Seat Page Table of Contents HandleCarry Infant CAR Seat Connection Infant Car Seat PartsUse Recommendations Height and Weight LimitsInfants With Special Needs Securing Infant In Car Seat Fig. c Securing infant in car seatSelecting a Vehicle Seating Location Options For Securing a Car Seat Latch SystemLatch System On This Car Seat Latch System On VehiclesInstallation of Infant Car Seat in Vehicle Removal Of Infant Car Seat From Base Zone Recline Indicator LineAttaching Infant Car Seat To Base Car Seat Release fig. a 1 HandleSecuring Base With Latch System Latch Lower Anchor ConnectorsStriped Zone GreenStorage Of Lower Anchorage Belt And Lower Anchor Connectors Removal Of Base Installed With LatchAnchor Connector Securing Base With Vehicle Seat Belt Fig. b Recline IndicatorLap Belt Center Section Lap BeltGreen Striped Zone Installation with Lap Belt OnlyFig. d Shoulder Belt Guide Installation with Lap And Shoulder BeltsRemoval Of Infant Car Seat From Vehicle Stroller or Travel System UseHarness Use and Adjustment Operation and AdjustmentHarness Adjuster Strap Changing Use Position and Harness LengthRod Adjuster Under CoverTab Recline Adjustment Handle Base AdjustmentHead Pillow Mommy’s Lap Infant InsertInfant Insert Infant Insert Pillow Canopy Vehicle Seat Belt SystemsTop Canopy Insert bottom canopy lever into bottom canopy bracketBelts Forward of Seat Bight Lap Belts Manually AdjustableLap Belts With Retractor Bight Belt Forward BuckleFig. e Front Door Lap or Shoulder Belt Mounted on Front Door fig. fLocking Clip stored in pouch on back of car seat Additional Information Care and CleaningRegistration Information Re-use After a CrashLimited Warranty
Top Page Image Contents