SET MENU
■Speaker distance C)SP DISTANCE
Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations. Thus, a certain amount of delay must be applied to the sound from each speaker so that all sounds will arrive at the listening position at the same time.
1 SOUND MENU | 1 SOUND MENU |
C)SP DISTANCE 1/2 | C)SP DISTANCE 2/2 |
. UNIT;;;;;;;;feet | . SUR. L;;;;;8.0ft |
FRONT L;;;10.0ft | SUR. R;;;;;8.0ft |
FRONT R;;;10.0ft | SB L;;;;;;;8.0ft |
CENTER;;;;;8.5ft | SB R;;;;;;;8.0ft |
SWFR;;;;;;10.0ft |
|
[p]/[p]:Up/Down | [p]/[p]:Up/Down |
[p]/[[]:Adjust | [p]/[[]:Adjust |
Unit UNIT
Choices: meters (m), feet (ft) Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
•Select “meters” to adjust speaker distances in meters.
•Select “feet” to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft) Initial setting:
FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)
CENTER: 2.60 m (8.5 ft)
SUR. L/SUR. R/SB L/SB R: 2.40 m (8.0 ft)
SP DISTANCE | Adjusted speaker |
FRONT L | Front left speaker |
|
|
FRONT R | Front right speaker |
|
|
CENTER | Center speaker |
|
|
SWFR | Subwoofer |
|
|
SUR. L | Surround left speaker |
|
|
SUR. R | Surround right speaker |
|
|
SB L | Surround back left speaker |
|
|
SB R | Surround back right speaker |
|
|
Notes
•The available speaker channels differ depending on the setting of the speakers.
•Instead of “SB L” and “SB R”, “SUR.B” is displayed if “SUR.B L/R SP” is set to either “SMLx1” or “LRGx1” (see page 66).
■Center speaker equalizer D)CENTER GEQ
Use this feature to adjust the
Control range:
Control step: 0.5 dB
Initial setting: 0 dB
1 SOUND MENU |
| |
D)CENTER GEQ |
| |
TEST | >OFF | ON |
. 100Hz | ;;;;;; | 0dB |
300Hz | ;;;;;; | 0dB |
1kHz | ;;;;;; | 0dB |
3kHz | ;;;;;; | 0dB |
10kHz | ;;;;;; | 0dB |
[p]/[p]:Up/Down [p]/[[]:Adjust
Test tone TEST
Use this feature to make adjustments for “CENTER GEQ” while listening to a test tone.
Choices: OFF, ON
•Select “OFF” to stop test tones and output the currently selected source component.
•Select “ON” to output test tones from the center and front left speakers.
■Low-frequency effect level E)LFE LEVEL
Use this feature to adjust the output level of the LFE (low- frequency effect) channel according to the capacity of your subwoofer or headphones. The LFE channel carries
Control range:
Control step: 1 dB
1 SOUND MENU
E)LFE LEVEL
.SPEAKER;;;;;;0dB HEADPHONE;;;;0dB
[p]/[p]:Up/Down [p]/[[]:Adjust
Speaker SPEAKER
Adjusts the speaker LFE level.
Headphone HEADPHONE
Adjusts the headphone LFE level.
Note
Depending on the settings of “LFE/BASS OUT” (see page 66), some signals may not be output at the SUBWOOFER OUTPUT jack.