JAI TS-1327EN, TS-9720EN, TS-2030EN Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com

Page 4

VIS-CAM System

WARNING

Changes or modifications to this unit not expressly approved by the party responsible for FCC compliance could void the user’s authority to operate the equipment.

VIS-CAM System Installation Manual

JAI Inc.

625 River Oaks Parkway

San Jose, CA 95134

Tel:(408) 383-0300

Tel:(800) 445-5444

Fax:(408) 383-0301

E-mail:trafficsales.americas@jai.com

trafficsales.emea@jai.com

www.jai.com

October 30, 2008


iv		Disclaimer

Image 4

Contents VIS-CAM System Page Warranty CertificationsVIS-CAM System DisclaimerMailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of FiguresStandard configuration of Serial settings for port List of Tables List of TablesVIS-CAM System Xii List of Tables Introduction Document OverviewProduct overview IntroductionSystem Components description Preparing for InstallationTraffic Light Sensor TLS300 Back shot VIS installation ViscamOperational Overview Installation Preparation Preparing for installationOver Lane Positioning Asynchronous triggering considerations Camera tilt considerationsCamera height versus trigger distance considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Side of Road Installation Typical side of road installationFlash and camera distances VIS-CAM System Preparing for Installation Installing the Vehicle Imaging System Installing the TNF-300 Traffic Light SensorInstalling the Vehicle Imaging Subsystem To install the Traffic Light SensorMounting pipe and flange Wire color SignalLight Sensor Cables Installing the Cameras Optional Side MountCamera mount template Electrical wiring for the VIS CAM installation X4 Pin # Wire Color Signal RemarksProperly wired X-4 connector VIS-CAM System Installing the J-Panel X1, X2 Pin # Wire Color Signal Remarks1 X1 and X2 VIS CAM 300/400 VIS CAM connections to the J-PanelTLS 300 to J-Panel connections X7 PinPower input to the J-Panel X6 Pin # Signal Description Connection to6 Power input connection 4 X8 LS RS485 Out Connector X8 to converter connector5 X14 Trigger Input Connector Trigger input connectorX14 Pin # Signal Description Connection to Trigger polarityX15 Pin # Signal Description Connection to X15 Lane ControllerArrow down negative going Test TriggerPin Signal Description Connection to Installing the TNF-31 FlashIllumination Options Trigger Options Installing The Laser Vehicle DetectorOptimal Illumination Distance Between Camera and TNF Connection for LVD to VIS CAM Wiring for LVD to VIS CAM X7 Pin # Signal Description Connection toVIS-CAM System Installing the Vehicle Imaging Subsystem Pre-Alignment Checklist System Set-UpPreparation for Alignment System Set-UpValidate the Installation Geometry Edit the alignment settings on the Setup ComputerTypical minimum plate heights and nominal plate heights Select the Camera to AlignConnect the Setup Computer to the Camera Example of a network connection using a local switchPerform Initial Lens Adjustment and Camera Aiming Drive and Park the Setup Vehicle CorrectlyProperly Position the License Plate Stand Initial Camera Alignment Display example Roll Bar Display example Finalize Lens Adjustments and Camera Aiming Perform Final Camera Mount and Lens AdjustmentsFocus Bar marker display Focus Bar Waveform display Focus Bar Waveform Display with waveform cursors Flash Head AlignmentOptimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional and Connector Description Appendix a Camera Functional & Connector DescriptionVIS-CAM System I/O Board Layout Component layout of the EN boardConnector specification Connector signal specificationsSignal levels VIS-CAM System X4 I/O Board Connection to J-panelElectrical interface on the I/O board Trigger input DescriptionConnector physical Interface . Physical interface table Power inputConnection to Pin Signal Description Panel Remarks Ethernet InterfaceTypical wiring diagram I/O Board Flash ConnectionExternal power requirement Output signal specificationDescription Connection DC Flash to an internally powered board VIS-CAM System IO board electrical interface TestConnector physical Interface Physical interface pinoutsConnecting the second AC flash VIS-CAM System Night Light TNC 100 Connection X7I/O Board Laser Vehicle Detector ConnectionTrigger Input Power OutputCommunication X1, X3 I/O Board Ethernet Test Connectors Connector physical Interface Connector tableTest setup Pin Signal Description Connection to RemarksVIS-CAM System VIS-CAM System X15 I/O Board Auxiliary power connector Cable SpecificationsRS485 and power CablesRecommended Cables Combined cable Ethernet, RS485 and powerMounting the cables Page Appendix B J-Panel Functional and Connector Description Appendix B J-Panel Functional & Connector DescriptionPanel Layout X1 J-panel connection to CameraTrigger output Description Signal parameters and conditionsElectrical interface on the J-Panel Connector physical Interface Physical interface table Pin Signal Description Connection to Remarks BoardIndicators LED indicatorsSwitches Switch labelsVIS-CAM System X2 J-panel connection to Camera Board and camera J-panel connection to camera FunctionalitySignal table Connector physical Interface Ethernet physical connections Category 5 or 6 ethernet wiring diagramConnector switches X3 Light Sensor ConnectionX4 Lane Controller Signal to J-Panel #2 Connector physical Interface Physical interface connectionsLED physical indicators Databus D0 and D1X5 Lane Controller Signal from J-Panel #1 DatasignalData signal X6, X7 24V DC PowerPhysical pin connections J-panel #1 Principle in the power distribution Connector specification Connector physical Interface RS485 physical connections X11 Ethernet Interface from CameraConnector physical Interface Physical connector description 10 X12 Ethernet Interface from Camera11 X14 External Trigger External Trigger connection FunctionalityTrigger 0 Electrical interface on the J-Panel Trigger 1 Electrical interface on the J-PanelCommon Lane Controller 12 X15 Lane Controller interface 6.12.1 FunctionalityTwo Lane Controllers Connector physical Interface Wago physical interface Connecting Lane Controller RS485 signal between J-PanelsAppendix C Two Cameras, One Flash Configuration Appendix C Two Cameras, One-Flash ConfigurationMaster Flash Connector Slave Laser Connector Master to slave connectionsAppendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal BlocksVIS-CAM System Appendix D Pluggable Terminal Blocks Appendix E Moxa N Port 5232 Configuration Appendix E Moxa N-Port 5232 ConfigurationBasic Settings Standard configuration of Network Settings Network SettingsStandard configuration of Serial settings for port Serial port 1 settingsConfiguration overview of serial port 1 TCP Server Mode Operating settings portData Packing VIS-CAM System Appendix F Multiple Moxa N-port Configuration Diagram Appendix F Multiple Moxa N port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Appendix H Troubleshooting Appendix H TroubleshootingFault Symptom Check/Possible Reason VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa