JAI TS-2030EN, TS-9720EN VIS-CAM System X15 I/O Board Auxiliary power connector, Cables, Ethernet

Page 74

VIS-CAM System

5.7X15: I/O Board Auxiliary power connector

Figure 62. Auxiliary power connector

5.7.1Functionality

Power outlet for auxiliary equipment.

5.7.2Connector physical Interface

Connector:		2 pole WAGO pluggable terminal block
PCB part:		WAGO 734-232
Cable part:		WAGO 734-202

	Connector pin #		Signal

	1		+24V (fused 0.5A) (self resetable)

	2		Gnd

5.8 Cables

In order to comply with EMC regulations the cable must be shielded and the wires must be twisted pairs. The cable used for the Ethernet signals must be minimum Cat 5e and preferably Cat 6. The wires used for power must be a minimum 0.5 mm2.

5.8.1Cable Specifications

5.8.1 (a) Ethernet:

Category

Characteristic impedance Number of twisted pairs Maximum cable diameter Maximum cable length

Cat 5e or preferably Cat 6

100Ω

15mm

100meters

5.8.1 (b) RS485 and power:

Characteristic impedance	120 Ω
Number of twisted pairs	4
Wire dimension	≥ 0.5mm2
Maximum cable diameter	15 mm
Maximum cable length	100 meters


62		Appendix A: Camera Functional & Connector Description

Image 74

Contents VIS-CAM System Page VIS-CAM System WarrantyCertifications DisclaimerMailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of FiguresStandard configuration of Serial settings for port List of Tables List of TablesVIS-CAM System Xii List of Tables Product overview IntroductionDocument Overview IntroductionTraffic Light Sensor TLS300 Preparing for InstallationSystem Components description Back shot VIS installation ViscamOperational Overview Over Lane Positioning Preparing for installationInstallation Preparation Camera height versus trigger distance considerations Camera tilt considerationsAsynchronous triggering considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Side of Road Installation Typical side of road installationFlash and camera distances VIS-CAM System Preparing for Installation Installing the Vehicle Imaging Subsystem Installing the Vehicle Imaging SystemInstalling the TNF-300 Traffic Light Sensor To install the Traffic Light SensorLight Sensor Cables Wire color SignalMounting pipe and flange Installing the Cameras Optional Side MountCamera mount template Electrical wiring for the VIS CAM installation X4 Pin # Wire Color Signal RemarksProperly wired X-4 connector 1 X1 and X2 VIS CAM 300/400 VIS-CAM System Installing the J-PanelX1, X2 Pin # Wire Color Signal Remarks VIS CAM connections to the J-PanelTLS 300 to J-Panel connections X7 PinPower input to the J-Panel X6 Pin # Signal Description Connection to6 Power input connection 4 X8 LS RS485 Out Connector X8 to converter connectorX14 Pin # Signal Description Connection to 5 X14 Trigger Input ConnectorTrigger input connector Trigger polarityArrow down negative going X15 Pin # Signal Description Connection toX15 Lane Controller Test TriggerIllumination Options Installing the TNF-31 FlashPin Signal Description Connection to Optimal Illumination Distance Between Camera and TNF Installing The Laser Vehicle DetectorTrigger Options Connection for LVD to VIS CAM Wiring for LVD to VIS CAM X7 Pin # Signal Description Connection toVIS-CAM System Installing the Vehicle Imaging Subsystem Preparation for Alignment Pre-Alignment ChecklistSystem Set-Up System Set-UpTypical minimum plate heights and nominal plate heights Validate the Installation GeometryEdit the alignment settings on the Setup Computer Select the Camera to AlignConnect the Setup Computer to the Camera Example of a network connection using a local switchProperly Position the License Plate Stand Drive and Park the Setup Vehicle CorrectlyPerform Initial Lens Adjustment and Camera Aiming Initial Camera Alignment Display example Roll Bar Display example Finalize Lens Adjustments and Camera Aiming Perform Final Camera Mount and Lens AdjustmentsFocus Bar marker display Focus Bar Waveform display Focus Bar Waveform Display with waveform cursors Flash Head AlignmentOptimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional and Connector Description Appendix a Camera Functional & Connector DescriptionVIS-CAM System I/O Board Layout Component layout of the EN boardSignal levels Connector specificationConnector signal specifications VIS-CAM System X4 I/O Board Connection to J-panelElectrical interface on the I/O board Trigger input DescriptionConnection to Pin Signal Description Panel Remarks Connector physical Interface . Physical interface tablePower input Ethernet InterfaceTypical wiring diagram I/O Board Flash ConnectionDescription Output signal specificationExternal power requirement Connection DC Flash to an internally powered board VIS-CAM System IO board electrical interface TestConnector physical Interface Physical interface pinoutsConnecting the second AC flash VIS-CAM System Night Light TNC 100 Connection X7I/O Board Laser Vehicle Detector ConnectionCommunication Power OutputTrigger Input X1, X3 I/O Board Ethernet Test Connectors Connector physical Interface Connector tableTest setup Pin Signal Description Connection to RemarksVIS-CAM System RS485 and power VIS-CAM System X15 I/O Board Auxiliary power connectorCable Specifications CablesMounting the cables Combined cable Ethernet, RS485 and powerRecommended Cables Page Panel Layout Appendix B J-Panel Functional and Connector DescriptionAppendix B J-Panel Functional & Connector Description X1 J-panel connection to CameraElectrical interface on the J-Panel Signal parameters and conditionsTrigger output Description Connector physical Interface Physical interface table Pin Signal Description Connection to Remarks BoardSwitches IndicatorsLED indicators Switch labelsVIS-CAM System X2 J-panel connection to Camera Board and camera J-panel connection to camera FunctionalitySignal table Connector physical Interface Ethernet physical connections Category 5 or 6 ethernet wiring diagramConnector switches X3 Light Sensor ConnectionLED physical indicators X4 Lane Controller Signal to J-Panel #2Connector physical Interface Physical interface connections Databus D0 and D1X5 Lane Controller Signal from J-Panel #1 DatasignalPhysical pin connections J-panel #1 X6, X7 24V DC PowerData signal Principle in the power distribution Connector specification Connector physical Interface RS485 physical connections X11 Ethernet Interface from CameraConnector physical Interface Physical connector description 10 X12 Ethernet Interface from Camera11 X14 External Trigger External Trigger connection FunctionalityTrigger 0 Electrical interface on the J-Panel Trigger 1 Electrical interface on the J-PanelTwo Lane Controllers 12 X15 Lane Controller interface 6.12.1 FunctionalityCommon Lane Controller Connector physical Interface Wago physical interface Connecting Lane Controller RS485 signal between J-PanelsAppendix C Two Cameras, One Flash Configuration Appendix C Two Cameras, One-Flash ConfigurationMaster Flash Connector Slave Laser Connector Master to slave connectionsAppendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal BlocksVIS-CAM System Appendix D Pluggable Terminal Blocks Basic Settings Appendix E Moxa N-Port 5232 ConfigurationAppendix E Moxa N Port 5232 Configuration Standard configuration of Network Settings Network SettingsStandard configuration of Serial settings for port Serial port 1 settingsConfiguration overview of serial port 1 Data Packing Operating settings portTCP Server Mode VIS-CAM System Appendix F Multiple Moxa N-port Configuration Diagram Appendix F Multiple Moxa N port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Fault Symptom Check/Possible Reason Appendix H TroubleshootingAppendix H Troubleshooting VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa