JAI TS-9720EN manual 12 X15 Lane Controller interface 6.12.1 Functionality, Common Lane Controller

Page 93

VIS-CAM System

6.11.4 Connector physical Interface
Table 33				Connector table

	Pin		Signal		Description	Connection to

	1		Trig0+		Positive trigger input to camera 0

	2		Trig0-		Negative trigger input to camera 0

	3		Trig1+		Positive trigger input to camera 1

	4		Trig1-		Negative trigger input to camera 1

6.12 X15: Lane Controller interface 6.12.1 Functionality

The signal path for the Lane Controller is shown in Figure 83. The signal lines symbolizes the two balanced RS485 wires.

6.12.1 (a) Common Lane Controller

If one lane controller is to be connected to camera 0 and camera 1, LC DATA terminals labelled D0 on X15 is used.

The signal runs to Camera 0 and is daisy chained back. When S2 is in position “OPEN” D0 is connected to Camera 1 and daisy chained back to connector X4. X4 has connection to a termination resistor that is activated when no plug is inserted into X4. If more J-Panels are to be connected to the same lane controller, see Figure 6.12.5.

6.12.1 (b) Two Lane Controllers

If separate lane controllers are to be connected to the two cameras, databus D0 is connected to Camera #0 and databus D1 is connected to Camera #1. Switch S2 must then be in position “TERM”. The 120 ? termination resistor is then connected between the RS485 wires.

Figure 83. Lane controller setup diagram.

6.12.2 Connector specification

Connector type:	5 pole WAGO pluggable terminal block
Connector on board:	WAGO 734-235
Cable part:	WAGO 734-205

6.12.3 Connector signal specifications

D0 and D1 are RS485 data bus signals from the Lane Controller.

Appendix B: J-Panel Functional & Connector Description

81

Image 93

Contents VIS-CAM System Page Certifications WarrantyVIS-CAM System DisclaimerMailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of FiguresStandard configuration of Serial settings for port List of Tables List of TablesVIS-CAM System Xii List of Tables Document Overview IntroductionProduct overview IntroductionPreparing for Installation System Components descriptionTraffic Light Sensor TLS300 Viscam Back shot VIS installationOperational Overview Preparing for installation Installation PreparationOver Lane Positioning Camera tilt considerations Asynchronous triggering considerationsCamera height versus trigger distance considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Typical side of road installation Side of Road InstallationFlash and camera distances VIS-CAM System Preparing for Installation Installing the TNF-300 Traffic Light Sensor Installing the Vehicle Imaging SystemInstalling the Vehicle Imaging Subsystem To install the Traffic Light SensorWire color Signal Mounting pipe and flangeLight Sensor Cables Optional Side Mount Installing the CamerasCamera mount template X4 Pin # Wire Color Signal Remarks Electrical wiring for the VIS CAM installationProperly wired X-4 connector X1, X2 Pin # Wire Color Signal Remarks VIS-CAM System Installing the J-Panel1 X1 and X2 VIS CAM 300/400 VIS CAM connections to the J-PanelX7 Pin TLS 300 to J-Panel connectionsX6 Pin # Signal Description Connection to Power input to the J-PanelX8 to converter connector 6 Power input connection 4 X8 LS RS485 Out ConnectorTrigger input connector 5 X14 Trigger Input ConnectorX14 Pin # Signal Description Connection to Trigger polarityX15 Lane Controller X15 Pin # Signal Description Connection toArrow down negative going Test TriggerInstalling the TNF-31 Flash Pin Signal Description Connection toIllumination Options Installing The Laser Vehicle Detector Trigger OptionsOptimal Illumination Distance Between Camera and TNF X7 Pin # Signal Description Connection to Connection for LVD to VIS CAM Wiring for LVD to VIS CAMVIS-CAM System Installing the Vehicle Imaging Subsystem System Set-Up Pre-Alignment ChecklistPreparation for Alignment System Set-UpEdit the alignment settings on the Setup Computer Validate the Installation GeometryTypical minimum plate heights and nominal plate heights Select the Camera to AlignExample of a network connection using a local switch Connect the Setup Computer to the CameraDrive and Park the Setup Vehicle Correctly Perform Initial Lens Adjustment and Camera AimingProperly Position the License Plate Stand Initial Camera Alignment Display example Roll Bar Display example Perform Final Camera Mount and Lens Adjustments Finalize Lens Adjustments and Camera AimingFocus Bar marker display Focus Bar Waveform display Flash Head Alignment Focus Bar Waveform Display with waveform cursorsOptimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional & Connector Description Appendix a Camera Functional and Connector DescriptionComponent layout of the EN board VIS-CAM System I/O Board LayoutConnector signal specifications Connector specificationSignal levels VIS-CAM System X4 I/O Board Connection to J-panelTrigger input Description Electrical interface on the I/O boardPower input Connector physical Interface . Physical interface tableConnection to Pin Signal Description Panel Remarks Ethernet InterfaceI/O Board Flash Connection Typical wiring diagramOutput signal specification External power requirementDescription Connection DC Flash to an internally powered board VIS-CAM System Test IO board electrical interfacePhysical interface pinouts Connector physical InterfaceConnecting the second AC flash X7I/O Board Laser Vehicle Detector Connection VIS-CAM System Night Light TNC 100 ConnectionPower Output Trigger InputCommunication Connector physical Interface Connector table X1, X3 I/O Board Ethernet Test ConnectorsPin Signal Description Connection to Remarks Test setupVIS-CAM System Cable Specifications VIS-CAM System X15 I/O Board Auxiliary power connectorRS485 and power CablesCombined cable Ethernet, RS485 and power Recommended CablesMounting the cables Page Appendix B J-Panel Functional & Connector Description Appendix B J-Panel Functional and Connector DescriptionPanel Layout X1 J-panel connection to CameraSignal parameters and conditions Trigger output DescriptionElectrical interface on the J-Panel Pin Signal Description Connection to Remarks Board Connector physical Interface Physical interface tableLED indicators IndicatorsSwitches Switch labelsBoard and camera J-panel connection to camera Functionality VIS-CAM System X2 J-panel connection to CameraSignal table Category 5 or 6 ethernet wiring diagram Connector physical Interface Ethernet physical connectionsX3 Light Sensor Connection Connector switchesConnector physical Interface Physical interface connections X4 Lane Controller Signal to J-Panel #2LED physical indicators Databus D0 and D1Datasignal X5 Lane Controller Signal from J-Panel #1X6, X7 24V DC Power Data signalPhysical pin connections J-panel #1 Principle in the power distribution Connector specification X11 Ethernet Interface from Camera Connector physical Interface RS485 physical connections10 X12 Ethernet Interface from Camera Connector physical Interface Physical connector descriptionExternal Trigger connection Functionality 11 X14 External TriggerTrigger 1 Electrical interface on the J-Panel Trigger 0 Electrical interface on the J-Panel12 X15 Lane Controller interface 6.12.1 Functionality Common Lane ControllerTwo Lane Controllers Connecting Lane Controller RS485 signal between J-Panels Connector physical Interface Wago physical interfaceAppendix C Two Cameras, One-Flash Configuration Appendix C Two Cameras, One Flash ConfigurationMaster to slave connections Master Flash Connector Slave Laser ConnectorAppendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal BlocksVIS-CAM System Appendix D Pluggable Terminal Blocks Appendix E Moxa N-Port 5232 Configuration Appendix E Moxa N Port 5232 ConfigurationBasic Settings Network Settings Standard configuration of Network SettingsSerial port 1 settings Standard configuration of Serial settings for portConfiguration overview of serial port 1 Operating settings port TCP Server ModeData Packing VIS-CAM System Appendix F Multiple Moxa N port Configuration Diagram Appendix F Multiple Moxa N-port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Appendix H Troubleshooting Appendix H TroubleshootingFault Symptom Check/Possible Reason VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa