JAI TS-9720EN Recommended Cables, Mounting the cables, Combined cable Ethernet, RS485 and power

Page 75

VIS-CAM System

5.8.1 (c) Combined cable (Ethernet, RS485 and power):

Number of twisted pairs	8
Maximum cable diameter	15 mm
Maximum cable length	100 meters

5.8.2Recommended Cables

Ethernet:	Cable, Cat 6 S-FTP 4x2xAWG24	JAI No. 2900.00.262
Power and RS485:	Cable Twisted Pair 4x2x0.5mm2	JAI No. 2900.00.267
Combined cable Cat 6, RS485 and power:		JAI No. 2900.00.268

5.8.3 Mounting the cables

Please refer to Section 3 on page 15 of this manual.

Appendix A: Camera Functional & Connector Description

63

Image 75

Contents VIS-CAM System Page Disclaimer WarrantyCertifications VIS-CAM SystemMailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of FiguresStandard configuration of Serial settings for port List of Tables List of TablesVIS-CAM System Xii List of Tables Introduction IntroductionDocument Overview Product overviewPreparing for Installation System Components descriptionTraffic Light Sensor TLS300 Viscam Back shot VIS installationOperational Overview Preparing for installation Installation PreparationOver Lane Positioning Camera tilt considerations Asynchronous triggering considerationsCamera height versus trigger distance considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Typical side of road installation Side of Road InstallationFlash and camera distances VIS-CAM System Preparing for Installation To install the Traffic Light Sensor Installing the Vehicle Imaging SystemInstalling the TNF-300 Traffic Light Sensor Installing the Vehicle Imaging SubsystemWire color Signal Mounting pipe and flangeLight Sensor Cables Optional Side Mount Installing the CamerasCamera mount template X4 Pin # Wire Color Signal Remarks Electrical wiring for the VIS CAM installationProperly wired X-4 connector VIS CAM connections to the J-Panel VIS-CAM System Installing the J-PanelX1, X2 Pin # Wire Color Signal Remarks 1 X1 and X2 VIS CAM 300/400X7 Pin TLS 300 to J-Panel connectionsX6 Pin # Signal Description Connection to Power input to the J-PanelX8 to converter connector 6 Power input connection 4 X8 LS RS485 Out ConnectorTrigger polarity 5 X14 Trigger Input ConnectorTrigger input connector X14 Pin # Signal Description Connection toTest Trigger X15 Pin # Signal Description Connection toX15 Lane Controller Arrow down negative goingInstalling the TNF-31 Flash Pin Signal Description Connection toIllumination Options Installing The Laser Vehicle Detector Trigger OptionsOptimal Illumination Distance Between Camera and TNF X7 Pin # Signal Description Connection to Connection for LVD to VIS CAM Wiring for LVD to VIS CAMVIS-CAM System Installing the Vehicle Imaging Subsystem System Set-Up Pre-Alignment ChecklistSystem Set-Up Preparation for AlignmentSelect the Camera to Align Validate the Installation GeometryEdit the alignment settings on the Setup Computer Typical minimum plate heights and nominal plate heightsExample of a network connection using a local switch Connect the Setup Computer to the CameraDrive and Park the Setup Vehicle Correctly Perform Initial Lens Adjustment and Camera AimingProperly Position the License Plate Stand Initial Camera Alignment Display example Roll Bar Display example Perform Final Camera Mount and Lens Adjustments Finalize Lens Adjustments and Camera AimingFocus Bar marker display Focus Bar Waveform display Flash Head Alignment Focus Bar Waveform Display with waveform cursorsOptimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional & Connector Description Appendix a Camera Functional and Connector DescriptionComponent layout of the EN board VIS-CAM System I/O Board LayoutVIS-CAM System X4 I/O Board Connection to J-panel Connector specificationConnector signal specifications Signal levelsTrigger input Description Electrical interface on the I/O boardEthernet Interface Connector physical Interface . Physical interface tablePower input Connection to Pin Signal Description Panel RemarksI/O Board Flash Connection Typical wiring diagramOutput signal specification External power requirementDescription Connection DC Flash to an internally powered board VIS-CAM System Test IO board electrical interfacePhysical interface pinouts Connector physical InterfaceConnecting the second AC flash X7I/O Board Laser Vehicle Detector Connection VIS-CAM System Night Light TNC 100 ConnectionPower Output Trigger InputCommunication Connector physical Interface Connector table X1, X3 I/O Board Ethernet Test ConnectorsPin Signal Description Connection to Remarks Test setupVIS-CAM System Cables VIS-CAM System X15 I/O Board Auxiliary power connectorCable Specifications RS485 and powerCombined cable Ethernet, RS485 and power Recommended CablesMounting the cables Page X1 J-panel connection to Camera Appendix B J-Panel Functional and Connector DescriptionAppendix B J-Panel Functional & Connector Description Panel LayoutSignal parameters and conditions Trigger output DescriptionElectrical interface on the J-Panel Pin Signal Description Connection to Remarks Board Connector physical Interface Physical interface tableSwitch labels IndicatorsLED indicators SwitchesBoard and camera J-panel connection to camera Functionality VIS-CAM System X2 J-panel connection to CameraSignal table Category 5 or 6 ethernet wiring diagram Connector physical Interface Ethernet physical connectionsX3 Light Sensor Connection Connector switchesDatabus D0 and D1 X4 Lane Controller Signal to J-Panel #2Connector physical Interface Physical interface connections LED physical indicatorsDatasignal X5 Lane Controller Signal from J-Panel #1X6, X7 24V DC Power Data signalPhysical pin connections J-panel #1 Principle in the power distribution Connector specification X11 Ethernet Interface from Camera Connector physical Interface RS485 physical connections10 X12 Ethernet Interface from Camera Connector physical Interface Physical connector descriptionExternal Trigger connection Functionality 11 X14 External TriggerTrigger 1 Electrical interface on the J-Panel Trigger 0 Electrical interface on the J-Panel12 X15 Lane Controller interface 6.12.1 Functionality Common Lane ControllerTwo Lane Controllers Connecting Lane Controller RS485 signal between J-Panels Connector physical Interface Wago physical interfaceAppendix C Two Cameras, One-Flash Configuration Appendix C Two Cameras, One Flash ConfigurationMaster to slave connections Master Flash Connector Slave Laser ConnectorAppendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal BlocksVIS-CAM System Appendix D Pluggable Terminal Blocks Appendix E Moxa N-Port 5232 Configuration Appendix E Moxa N Port 5232 ConfigurationBasic Settings Network Settings Standard configuration of Network SettingsSerial port 1 settings Standard configuration of Serial settings for portConfiguration overview of serial port 1 Operating settings port TCP Server ModeData Packing VIS-CAM System Appendix F Multiple Moxa N port Configuration Diagram Appendix F Multiple Moxa N-port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Appendix H Troubleshooting Appendix H TroubleshootingFault Symptom Check/Possible Reason VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa