JAI CV-M536, CV-M539, CV-M538 operation manual Jumper Settings, Pixel Clock Output

Page 18

CV-M536/538/539

7.3. Jumper Settings

Caution on Jumper Setting.

Before making any mode or jumper setting turn the power OFF.

Jumpers for mode setting are found on the boards PK8054 & PK8057.

The following modes are available with jumper setting:

Input/Output Mode of HD/VD signal. (HD/VD input is factory setting)

Edge Pre-select Mode. (Factory setting)

Pulse Width Control Mode

Start/Stop Trigger Mode

Long Time Exposure Mode

Set the jumpers according to the list below in 7.3.1. and 7.3.2.

The jumper positions are shown in “7.4.1. Bo rd 8054 Side B” and “7.4.2. Board 8057 Side A”.

SwitchJumperSW2 oninputHD/VDExtHD/VDPK8057.*) in/outHD/VDoutputisInt.shownEdgeselectinpre“7-.2.ExternalSW2controlwidthPulseontriggerPK8057triggerStart/modesstopBoard”Longexposetime.

Remarks

7.3.R127. Jumper Shorton PK8054ShortBoard Short

Short

Open

Short

FactorysetSHORT

 

 

 

 

 

 

 

 

 

 

 

 

7.3.2. Jumper onHD/VDPK8057in/outBoard

 

Externaltriggermodes

Longtime

 

Remarks

Jumper

HD/VDExt.

HD/VDInt.

Edgepre-

widthPulse

Start/stp

HD

 

21

input*)

output

 

select

control

trigger

expose

 

*) Factory Setting

 

 

 

 

 

 

 

 

 

 

43

Short

Open

 

Short

Short

ShortOpen

Open

VDinput/output..Factorysetinput

JP89657

Short

 

Short

Longtimeintegration

JP

0

Open

Open

 

Open-

-

 

-

Open-

Pixelclockout.FactorysetOPEN

 

Short

Short

 

Short

Open

Short

Short

Pulsewidth

 

SW12-21

ON

-

 

ON

ON

ON

 

ON

HDVin75Ohmterm.FactorysetON

*) Factory Setting

7.3.3. Pixel Clock Output

To use pixel clock output (TTL level: 4.0 V), make the jumper JP11 on PK8057 board shorted-circuited. The jumper position is shown in “7.4.1. Board PK8057 Side A”.

Pixel clock pulse will be output from pin no.9 of 12-pin multi-connector.

Caution for Pixel Clock Output.

When the pixel clock is enabled, it may cause interference with external equipment if it not properly shielded.

- 17 -

Image 18
Contents CV-M536/538/539 Declaration of Conformity Table of Contents General Standard CompositionMain Features Locations and Functions Pin Multi-connector DC-IN/SYNC Pin Multi-connector TriggerPin Assignment Input/Output of HD/VD Signal Functions and OperationsEIA Non-interlaced / Field accumulation mode Edge pre-select mode for non-interlace onlyCcir Non-interlaced / Field accumulation mode Pulse Width Control ModePulse width control mode for non-interlace only Start/Stop Trigger Mode CV-M536/538/539 Long Time Exposure Mode EIA CcirCV-M536/538/539 Mode Setting Table for SW 1 SettingTable for Shutter Time SW2 on PK8057 Board Jumper Settings Pixel Clock OutputLocation of SW2 and Jumpers Board PK8054 Side BBoard PK8057 Side a Adjustment of Video Signal Output Level External Appearance CCUHead Specifications Spectral SensitivityPrecautions Typical CCD CharacteristicsAppendix Camera type CV-M536/538/539 Scanning system Users Mode Settings Users ModificationsUser’s Record Revision Revision E Serial No