Nikon WP-CP3 user manual Do not dive while holding

Page 4

Do not dive while holding

To prevent injury caused by the case striking the body, do not jump or dive into water while holding the WP-CP3.

Do not use below 40 m

Do not use at depths below 40 m (130´). Failure to observe this precaution could result in leakage or other malfunction.

Keep the case watertight

Do not clean the case with a high-pres- sure jet. Do not open the case where it would be exposed to dust or sand, and be sure to remove any foreign objects from the O-ring and any parts of the case that are in contact with the O- ring before closing the case. Failure to observe these precautions could result in leakage.

Do not exposure to high temperatures Do not expose the product to tem- peratures over 40 °C (104 °F). Failure to observe this precaution could cause the product to warp, resulting in leakage.

Observe caution when operating the flash

Using the flash close to your subject’s eyes could cause temporary visual impairment. Particular care should be observed if photographing infants, when the flash should be no less than one meter (39˝) from the subject.

ii

Image 4
Contents Waterproof Case WP-CP3 User’s ManualFor Your Safety Turn camera off immediately in the event of malfunctionDo not dive while holding Iii Temperature Table of Contents Important Use Only with Compatible Cameras Life-Long LearningPackage Contents IntroductionParts of the WP-CP3 Attaching the StrapIntroduction Follow these steps when using the waterproof case OverviewTurn the camera on Adjust settings Take pictures Caring for the O-ring StorageCheck for Leaks Check for Leaks Select Underwater mode Insert the CameraReady the Camera BatteriesInsert the Camera Turn the camera off Release the buckleLatch forward and open the buckle Open the casePerform a Final Check Insert DesiccantReplacing the Desiccant Close the Case Check for Leaks Again Take Pictures Adjust SettingsTurn the Camera On Take Pictures Don’t Block the ShotUse the Monitor Era is in the case. Use the monitor to frameClean the Case Wash the case in fresh waterDrying the Case Removing the CameraCleaning the Interior of the Case Do Not Exposure to Sunlight or HeatMaintenance Caring for the O-ringDo Not Use Force or Sharp Objects Replacing the O-ringCleaning Grease the O-ringOptional Accessories Technical NotesStorage SpecificationsBenutzerhandbuch Sicherheitshinweise WarnhinweiseVerwenden Sie das Produkt nur bis maxi- mal 40 m Wassertiefe Achtung Vermeiden einer UndichtigkeitTemperatur Inhaltsverzeichnis Einsetzen der Kamera in das GehäuseHinweise Immer auf dem neuesten StandEinführung Der PackungsinhaltDas Unterwassergehäuse WP-CP3 in der Übersicht Befestigen des TrageriemensLöschtaste Übersicht Verwenden des WP-CP3Schritt 4 Fotografieren Schließen Sie das Gehäuse Schritt 1 Überprüfen der DichtigkeitVerriegeln Sie das Gehäuse Testen Sie die Bedienelemente Prüfen Sie auf DichtigkeitPrüfen Sie, ob Wasser in das Gehäuse einge- drungen ist Schritt 2 Einsetzen der Kamera in das Gehäuse Vorbereiten der KameraWählen Sie den Unter Wasser Modus Entfernen Sie den Trageriemen der KameraÖffnen Sie das Gehäuse Einsetzen der KameraSetzen Sie die Kamera ein Einlegen des Trockenmittels Letzte KontrolleSchließen des Gehäuses Klappen Sie das Gehäuse zuSchritt 3 Erneutes Überprüfen der Dichtigkeit Einschalten der Kamera Schritt 4 FotografierenEinstellen der Kamera Fotografieren Halten Sie die Kamera aufnahmebereitWählen Sie den Bildausschnitt Stellen Sie scharf und lösen Sie ausSchritt 5 Reinigen des Unterwassergehäuses Spülen Sie das Unterwassergehäuse unter klarem Wasser abWischen Sie das Gehäuse trocken Nehmen Sie die Kamera herausLassen Sie das Gehäuse an einem geeigneten Ort trocknen Reinigen der Innenseite des GehäusesPflegeanleitung Pflege des O-RingsNehmen Sie den O-Ring heraus Riss Kontrollieren Sie den O-RingSetzen Sie den O-Ring ein Fetten Sie den O-RingÜberprüfen Sie die Dichtung Technische Hinweise AufbewahrungTechnische Daten Optionales ZubehörManuel de lutilisateur Pour votre sécurité ’utilisez pas votre matériel en présence de gaz inflammableMaintenez le caisson étanche Eviter l’entrée d’eau Température Table des matières Avertissements Formation permanenteContenu de la boîte Descriptif du WP-CP3 Fixation de la dragonneIntroduction Effectuer une der Présentation généraleNière vérification Son Étape 3 Vérifier à nouveau l’étanchéité du caisson Entretien du joint torique RangementFermer le caisson Étape 1 Vérifier l’étanchéité du caissonImmerger le caisson Vérifier l’étanchéité Vérifier que l’eau n’est pas rentrée dans le caissonPréparer l’appareil photo Accus/ pilesIntroduire l’appareil photo Ouverture du caissonRemplacement de l’absorbeur d’humidité Placer l’absorbeur d’humiditéEffectuer une dernière vérification Le joint torique est-il craquelé ou abîmé?Fermer le caisson Étape 3 Vérifier à nouveau l’étanchéité du caisson Mettre l’appareil sous tension Étape 4 PhotographierRégler les paramètres Photographier ’entravez pas la prise de vueUtiliser le moniteur Mettre au point et déclencherÉtape 5 Nettoyer le caisson Nettoyer le caisson dans de l’eau douceEssuyage du caisson Retrait de l’appareil photoNettoyage de l’intérieur du caisson Remplacement du joint torique Entretien du joint toriqueRetirer le joint torique Inspecter le joint toriqueGraisser le joint torique NettoyageAccessoires optionnels Remarques techniquesRangement Caractéristiques사용설명서의 일부 또는 전부를 무단으로 전재하는 것은 엄 격히 금지합니다

WP-CP3 specifications

The Nikon WP-CP3 is a versatile waterproof case designed to protect select Nikon cameras, allowing photography enthusiasts to explore underwater environments without compromising their equipment. With its robust construction and intuitive design, the WP-CP3 enables users to capture stunning images and videos in challenging conditions.

One of the most notable features of the WP-CP3 is its impressive waterproof depth rating. The case can withstand depths of up to 30 meters, making it suitable for a wide range of water activities, from snorkeling to scuba diving. This depth capability ensures that photographers can confidently venture into aquatic environments, knowing their camera is protected from water damage.

The WP-CP3 is constructed from durable polycarbonate material, providing both strength and lightweight portability. Its transparent design allows for easy framing and composition of shots underwater while maintaining visibility of the camera controls. This is particularly important for photographers who require precise adjustments in lighting and focus even when submerged.

In terms of usability, the WP-CP3 incorporates ergonomically designed controls, enabling photographers to access essential functions without removing the camera from the case. Buttons for shutter release, zoom control, and mode selection are intuitively placed for easy operation. This thoughtful design ensures that users can quickly capture moments without fumbling, even in demanding conditions.

The WP-CP3 also features an anti-fog system, which helps to minimize condensation and maintain clarity in underwater shots. This technology is valuable for photographers who frequently transition between different temperatures or move from above water to below, ensuring a seamless shooting experience.

Compatibility is another strong point of the WP-CP3. Designed for specific Nikon models, it seamlessly integrates with select cameras, allowing full functionality and performance without hinderance. This tailored fit means that users do not have to sacrifice quality or functionality when utilizing the case.

In summary, the Nikon WP-CP3 is a reliable and robust waterproof case that empowers photographers to capture breathtaking underwater imagery. With its impressive depth rating, durable construction, intuitive controls, and anti-fog technology, the WP-CP3 stands out as an essential accessory for anyone looking to push the boundaries of their photography in aquatic environments. Whether exploring coral reefs or capturing the beauty of underwater wildlife, the WP-CP3 ensures that photographers can do so with confidence and ease.