Yamaha RX-SL100RDS Sound suddenly, Goes off, Only the speaker on, One side can be, Heard, Speaker

Page 54

TROUBLESHOOTING

Problem

Cause

Remedy

Refer to

page

 

 

 

 

 

 

 

The sound suddenly

The protection circuit has been activated

Check that the impedance selector setting is correct.

10

goes off.

because of a short circuit, etc.

 

 

Check the speaker wires are not touching each other

—

 

 

 

 

and then turn this unit back on.

 

 

 

 

 

 

The sleep timer has turned the unit off.

Turn on the power, and play the source again.

—

 

 

 

 

 

The sound is muted.

Press MUTE to cancel a mute.

20

 

 

 

 

Only the speaker on

Incorrect cable connections.

Connect the cables properly. If the problem persists,

12—13

one side can be

 

the cables may be defective.

 

heard.

 

 

 

Incorrect balance settings in the BASIC

Adjust the Speaker Level settings.

17

 

 

menu.

 

 

 

 

 

 

Only the center

When playing a monaural source with a

 

 

speaker outputs

CINEMA DSP program, the source signal

 

 

substantial sound.

is directed to the center channel, and the

 

 

 

front and surround speakers output effect

 

 

 

sounds.

 

 

 

 

 

 

No sound from the

The output level of the center speaker is

Raise the level of the center speaker.

17

center speaker.

set to minimum.

 

 

 

 

 

 

 

“Center” in the SOUND menu is set to

Select the appropriate mode for your center speaker.

41

 

None.

 

 

 

 

 

 

 

One of the sound field programs (except

Select another sound field program.

20

 

for 6ch Stereo) has been selected.

 

 

 

 

 

 

No sound from the

The output level of the surround speakers

Raise the output level of the surround speakers.

17

surround speakers.

is set to minimum.

 

 

 

 

 

 

 

“Surround L/R” in the SOUND menu is

Select the appropriate speaker mode for the surround

41

 

set to None.

left and right speakers.

 

 

 

 

 

 

A monaural source is being played with

Press STEREO/EFFECT to turn on the sound fields.

—

 

STEREO/EFFECT set to STEREO.

Then select another sound field program.

 

 

 

 

 

No sound from the

“Surround L/R” in the SOUND menu is

If the speaker mode for the surround left and right

41

surround back

set to None.

speakers is set to None, the speaker mode for the

 

speaker.

 

surround back speaker is automatically set to None.

 

 

 

Select the appropriate speaker mode for the surround

 

 

 

left and right speaker mode.

 

 

 

 

 

 

“Surround Back” in the SOUND menu is

Select Large or Small.

41

 

set to None.

 

 

 

 

 

 

 

PLII/PLIIx is set to “PLII” when playing a

Select PLIIx. Press q/DTS to select a PLIIx sound

50

 

2-channel source.

field program.

 

 

 

 

 

No sound from the

“LFE/Bass Out” in the SOUND menu is

Select SWFR or Both.

41

subwoofer.

set to FRONT when a Dolby Digital or

 

 

 

DTS signal is being played.

 

 

 

 

 

 

 

“LFE/Bass Out” in the SOUND menu is

Select Both.

41

 

set to SWFR or FRONT when a 2-channel

 

 

 

source is being played.

 

 

 

 

 

 

 

The source does not contain low bass

 

 

 

signals.

 

 

 

 

 

 

52

Page 53 Page 55
Image 54
Page 53 Page 55
Contents RX-SL100RDS For U.K. customers Special Instructions for U.K. ModelContents Features Getting Started Supplied accessoriesInstalling batteries in the remote control Please check that you received all of the following partsControls and Functions Front panelRemote control AMP mode Volume + Using the remote controlHandling the remote control SET MenuFront panel display Speaker Setup Speaker placementCable tags Return the tab to secure the wireSpeaker connections 10 mm 3/8Impedance Selector switch Impedance Selector switchSurround terminals Speaker connectionsFront terminals Surround Back terminalsConnecting a TV Before connecting componentsConnecting other components Connecting AV componentsDigital audio connections Video 2 jacks on the front panelOptical out DVD player DTV or Frequency Step Asia and General Models only Connecting the antennasConnecting the AM loop antenna Included White BlackConnecting the AC power Connecting the powerTurning on the power Front panel Remote controlBasic Setup Using Basic setupSpeaker Set Up Enter Speaker LevelPress k/n repeatedly to select Room Size, then press Enter Press k/n repeatedly to select Yes or No, then press EnterMemory back-up Playback Press STANDBY/ON to turn on the powerAdjust the volume to the desired output level Basic operationsPress Mute on the remote control Remote control operationTo listen with headphones Silent Cinema Selecting sound field programsFront panel operation Press DSP, then rotate VOLUME/SELECT within 5 secondsPress Night on the remote control Listening at nightAutomatic tuning TuningAutomatic and manual tuning LightsManual tuning DisappearsHold down VOLUME/SELECT for more than 6 seconds Presetting stationsAutomatically presetting FM stations FM appears on the front panel displaySee page 22 for tuning instructions Selecting preset stationsManually presetting stations Tune into a stationReceiving RDS stations Press PTY Seek Mode to set this unit in the PTY Seek mode Changing the RDS modeTo cancel this function Press u Preset d to select the desired program typeEON function To change the Standby Scart setting RecordingThen Type Button Sound Field Program DescriptionsFor Hi-Fi DSP programs For musicVideo For CINEMA-DSP programsFor audio For movieCanceling the sleep timer Using the sleep timerSetting the sleep timer Advanced OperationsPRO Logic Enhanced Enjoying 2-channel softwarePRO Logic Operation AdvancedVirtual Cinema DSP Press k/n repeatedly to select Input Mode, then press hInput Mode Press AMP to select the AMP mode Press l / h to adjust the speaker output levelDisplaying information about the input Source Using the test tone Press Test on the remoteControl Sound menu SET MenuBasic menu Input menuChanging parameter settings Press AMP, then press SET Menu to enterPress k/n repeatedly to select a menu, then press h SP Tone Control Speaker tone control Sound menuCenter SP. GEQ Center speaker graphic Equalizer HP Tone Control Headphone toneSpeaker Set Speaker set SP Distance Speaker distance LFE Level Low-frequency effect levelDynamic Range Dynamic range Optical Input Input menuInput Assign Input assignment Choices VCR, VIDEO1, DTV/CBL, DVD/CDInput Mode Input mode Option menuAudio Mute Mute Display Dimmer Display dimmerMemory Guard Memory guard Tuner Freq/Step Tuner frequency stepControlling this unit Remote Control FeaturesControl area Controlling other componentsSetting a code Setting manufacturer codesDefault codes Hold down Code SET while doing steps 2Controlling other components ENTWhat is a sound field Editing Sound Field ParametersElements of a sound field DSP Level DSP level Delay DelayDimension Dimension For 6ch StereoTroubleshooting GeneralOnly the speaker on Sound suddenlyGoes off One side can beSwitches to Or DTS indicator onVolume level Standby modeTuner Remote control Does not work orFunction properly Glossary Virtual Cinema DSP PCM Linear PCMSampling frequency and number Quantized bits Specifications VCR WC19140-1

RX-SL100RDS specifications

The Yamaha RX-SL100RDS is a versatile and compact stereo receiver that caters to both casual listeners and audiophiles alike. Its sleek design and advanced technologies provide an enjoyable audio experience, making it a great addition to any home entertainment setup.

One of the standout features of the RX-SL100RDS is its ability to deliver high-quality sound. Powered by Yamaha’s proprietary technology, the receiver boasts a dynamic power output that allows it to drive speakers with clarity and precision. The high-fidelity audio performance is complemented by the advanced digital signal processing, which enhances the overall listening experience across various music genres.

In terms of connectivity, the RX-SL100RDS supports a range of input options, including multiple analog and digital inputs, allowing users to connect various audio sources seamlessly. The inclusion of Bluetooth technology enables wireless streaming from smartphones, tablets, and other compatible devices, affording users enhanced flexibility and convenience.

The built-in RDS (Radio Data System) tuner is another noteworthy feature, enabling users to access a wide array of FM stations along with useful information, such as station names and song titles. The tuner’s automatic memory function makes it easy to store preferred stations for quick access.

Yamaha's YPAO (Yamaha Parametric room Acoustic Optimizer) technology is integrated into the RX-SL100RDS, allowing for automatic audio calibration. This innovative feature analyzes the room's acoustics and adjusts the output for optimal sound quality, providing an enhanced auditory experience in any environment.

The design of the RX-SL100RDS is both stylish and functional. Its compact size makes it suitable for smaller spaces, without compromising on performance. The user-friendly interface, complete with an easy-to-read display, ensures that navigating through settings and options is hassle-free.

Additionally, the receiver is equipped with advanced thermal management systems that provide reliable performance during extended listening sessions. With its durable build quality and classic Yamaha aesthetics, the RX-SL100RDS is not only reliable in performance but also visually appealing.

Overall, the Yamaha RX-SL100RDS is a feature-packed stereo receiver that combines advanced audio technology, user-friendly connectivity options, and elegant design, making it an excellent choice for anyone looking to enhance their home audio experience.
Top Page Image Contents