Siemens 6AU1900-1AB32-0BA0 configurationmanual Target device parameters, Coordinates

Page 73

Functions 4.9 Specify parameters for target device

Notice

If you specify a scaling, you can show and hide the scaled curve via the menu Cam > Representation parameters > Display scaling.

If the scaled curve is displayed, you cannot edit the original curve in the diagram displays.

4.9.2Target device parameters

coordinates

Specify the coordinates for the target device here.

You can set the following parameters:

Table 4-4

Parameters in the Coordinates tab (Target Device Parameters window)

 

 

 

 

 

 

Field/button

Explanation/instructions

Master Range

You specify the master range (definition range) of the curve via start and

 

 

 

end points. Cam segments must lie within this master range (see also

 

 

 

Master range under S Diagram (Master) properties).

 

Start

 

Enter the start point of the curve, or the start of the master range of the

 

 

 

curve here.

 

End

 

Enter the end point of the curve, or the end of the master range of the

 

 

 

curve here.

Execution type

The Execution type specifies the interpolation of the cam by the target

 

 

 

device at the boundary points of the master range.

 

Non-cyclic

If you select the Non-cyclicexecution type. The cam cycle ends when

 

 

 

the end value of the curve is reached. The function values of the cam

 

 

 

(slave position) at the start and end point of the master range are

 

 

 

normally different.

 

 

 

Note:

 

 

 

If you activate Non-cyclic, the master range in the horizontal direction is

 

 

 

displayed once.

 

Cyclic absolute

If you select the cyclic absolute execution type, a return is made from the

 

 

 

end value of the slave axis to the start point of the slave axis and the

 

 

 

cam is repeated. The function values of the cam (slave position) at the

 

 

 

start and end point of the master range are identical. Possibly an

 

 

 

identical value (average value) is forced from the target device.

 

 

 

Note:

 

 

 

If you activate Cyclic absolute, the master range in the horizontal

 

 

 

direction can be displayed repeatedly.

CamTool

4-31

Configuration Manual, 12.2004, 6AU1900-1AB32-0BA0

Image 73
Contents Configuration Manual ConfiguringPreface DescriptionSafety Guidelines Scope Contents of manualStandards Information blocksHotline Simotion documentationPreface Siemens Internet address Additional supportPage Table of contents Index Tables Table of contentsCamTool Configuration Manual, 12.2004, 6AU1900-1AB32-0BA0 Page Basic functions IntroductionPage System requirements Installing Simotion CamToolInstalling Simotion CamTool Deinstalling Simotion CamToolDeinstalling Simotion CamTool Installing the Software Deinstalling Simotion CamToolOverview ContentChanging the representation using the toolbar Changing the representation using the toolbarConfiguring Customizing the Working Area Display Customizing the Working Area DisplayZoom tool with pressed Shift key ConfiguringMaximizing the working area Maximizing working areaAdding a cam to a Scout project using CamTool ContentConfiguring 3.3 Editing a Cam with CamTool Editing a Cam with CamToolInserting a cam in a Scout project Configuring Editing a Cam with CamToolEditing a Cam with CamTool Edit cam created with CamEdit with CamToolOpen with CamTool a cam created with CamEdit Configuring 3.3 Editing a Cam with CamTool Importing a cam Import cam from text fileClick a diagram to show the Cam menu Edit imported cam Upload cam from Simotion deviceCam uploaded from Simotion device Upload camClick a diagram to show the Cam menu Save cam Configuring 3.4 Save camEdit uploaded cam Save camCustomize the display of the cam Show/hide diagramDisplay the cam Change axis representation parameters Configuring 3.5 Customize the display of the camChange axis representation parameters Properties Cyclic relative execution type, you can select Change diagram representation parameters Change diagram representation parametersDisplayed curve Change lines and fonts representation parameters Representation parameters Change lines and fonts representation parametersRepresenting a horizontal auxiliary line in a diagram Displaying auxiliary lines in the diagram17 Displaying a horizontal auxiliary line Configuring Download cam to Simotion device Deleting an auxiliary line in a diagramDownload cam to Simotion device Moving the position window along an auxiliary lineDownload cam to Simotion device Configuring 3.6 Download cam to Simotion devicePage Functions Structure of a cam Structure of a camFunctions Structure of a cam Fixed Point Definition Fixed pointInsert fixed point DefinitionFunctions Fixed point Changing the velocity at the position of a fixed point Change fixed point positionChange fixed point position Change velocity at fixed pointChange acceleration at fixed point Changing the acceleration at a fixed point positionDelete fixed point Straight lineDefinition straight line Delete fixed pointInsert straight line Insert straight lineFunctions Straight line Change straight line position Change straight line positionChange velocity along a straight line Changing the velocity along a straight lineDelete straight line Sine curveInsert sine curve Deleting a straight lineFunctions Sine curve Change sine curve position Change sine curve positionChange sine curve definition range Change sine curve definition rangeDelete sine curve Arc Sine CurveInsert arc sine curve Delete sine curve11 Insert arc sine curve Change arc sine curve position Change arc sine curve positionChange arc sine curve definition range Change arc sine curve definition rangeDelete arc sine curve Delete arc sine curveInterpolation Point Definition Interpolation pointInsert interpolation point Insert interpolation pointFunctions 4.7 Interpolation point Changing the interpolation point positionChanging an Interpolation Point Position Delete interpolation pointDelete interpolation point Optimizing a Cam Optimizing a CamFunctions Optimizing a Cam Optimize transition Optimize transition20 Optimizing a cam with handle using drag&drop Type Interpolation Curve propertiesParameters Velocity for calculations in the Simulation Settings windowLimit values Functions Specify parameters for target device Specify parameters for target deviceSpecify parameters for target device Functions Specify parameters for target deviceCoordinates Target device parametersFunctions 4.9 Specify parameters for target device Interpolation Scaling Slave axis Basic scaling Specify simulation settings Specify simulation settingsSpecify simulation settings Functions 4.10 Specify simulation settingsFunctions Specify simulation settings Simulation settingsMaster tab Slave tab Export cam as text file Edit cam created with CamTool with CamEditConvert a cam created with CamTool for CamEdit Functions Edit cam created with CamTool with CamEditExport cam as text file Print camPrint cam Functions Print camPage Index Index Index-3 Index-4