Sharp VL-NZ100S manual Appendix Battery Pack, Charging, Storage, Use

Page 86

Appendix

Battery Pack

This camcorder uses a lithium-ion type battery pack.

Charging

Charge the battery pack immediately (or a day) before use. The battery pack gradually self-discharges even if stored in a fully charged state.

Charge the battery pack between 10°C and 30°C.

Fully charge the battery pack. Use of an insufficiently charged battery pack will shorten actual time of use.

Refresh (discharging before charging) is unnecessary.

Storage

Store the battery pack in a fully discharged state.

Store the battery pack in a dry, cool place.

When storing a fully charged battery pack, put the cover on it so that the “CHARGE” mark printed on the label is seen through the

window, as shown.

Label

Battery pack

CHARGE

Window

Cover

Appendix

75

Use

To conserve battery power, be sure to turn off the camcorder power when not in use.

Battery consumption may vary depending on the condition of use. Recording with many starts and stops, frequent zooming, and recording in low temperatures will shorten actual recording times.

Use of a weak battery pack may cause loss of power while operating the camcorder. Use a fully charged battery pack to protect both the battery pack and the unit.

It is recommended that you have enough battery packs on hand to handle two or three times your estimated recording time. See page 20 for the approximate times of actual recording for the battery packs.

Battery power is consumed even when the camcorder power is turned off. If you are not going to use your camcorder immediately, remove the battery pack (see page 9).

Note:

Use only SHARP BT-L225 or BT-L445 battery packs. These are designed specifically for use with this camcorder.

When storing a battery pack that is not fully charged, put the cover upside down so that only the battery pack casing can be seen through the window.

Cautions:

Improper handling of the battery pack may present a risk of fire or explosion. Pay close attention to the following:

Do not allow metallic objects to come in contact with the terminals. This can cause a short circuit.

Do not disassemble or repair the battery pack by yourself.

Do not use any battery charging equipment other than that designed for use with these battery packs.

Do not place the battery pack under direct sunlight or in excessively hot places (over 60°C) such as the dashboard of cars.

Do not expose the battery pack to moisture or water.

Do not drop the battery pack or subject it to strong force.

Keep the battery pack out of reach of children.

Dispose of used battery packs promptly. Do not dispose of them in fire.

To protect the terminals, put the cover on the battery pack when it is not in use.

Notes:

The battery pack will become warm during charging and use. This is not a malfunction.

The battery pack has a limited service life. If the period of use becomes noticeably shorter with a normal charge, the battery pack is at the end of its service life. Replace it with a new battery pack.

If the terminals of the battery pack are dirty, wipe the terminals with a soft, dry cloth.

VL-NZ100H-074-080

75

02.2.14, 10:05 AM

Image 86
Contents Sharp Corporation Gedruckt in Japan Imprimé au Japon TINSLA006WJZZ 02P03-JKGPower supply Special Note for Users in the U.K Supplied Accessories Optional Accessories When using your camcorder in a cold envi IiiWhat is dew formation? Dew FormationAvailable mode Precautions Dirty Video HeadsUsing a Cleaning Tape Commercially Available Causes of video head cloggingContents Contents Digital Still Camera Features Appendix ViiiPart Names Compartment doorMedia Selection Card selectionOperation References Pp , 30On-screen Display Index TAPE-CAMERA modeTAPE-VCR mode Operation ReferencesCARD-CAMERA mode CARD-VCR modeManual screens On-screen indicators on/offExample screens shown are for TAPE-CAMERA mode AS S E T T E New one see Setting seeProperly inserted see Card has no images recorded in the format the camcorder canRemoving Attaching and Removing the Battery PackAttaching Preparation1Fully charge the battery pack Charging the Battery PackExtending battery pack life BatteryPowering the Camcorder from an AC Outlet PreparationPerform above, then take out the cassette Inserting and Removing a CassetteInserting Close the card slot cover About the write-protect switchInserting and Removing a Card Installing the Lithium Battery InstallingT T I NG Setting the DateTime Attaching the Wrist Strap Changing to the 12-hour Time ModeAttaching the Lens Hood Press l or m to select 12H, then press the SET buttonUsing the Lens Cap Attach the strap to the lens cap as shown belowBasic posture Tips on Recording PositionsHolding the camcorder Shooting from a high angleCARD-CAMERA mode CARD-VCR mode Selecting the Camcorder ModeTAPE-CAMERA mode TAPE-VCR mode Camcorder modesTo pause recording Easy Camera Recording on Tape in Full Auto ModeTo turn the power off Press the REC START/STOP button to begin recordingBasic Operations Camera Recording Zooming Auto FocusMacro Shots ZoomingRemaining Battery Power Display Remaining Recording Time DisplayTo stop playback Using Earphones Commercially AvailableTape Playback Video Search Volume ControlStill Searching for a Scene Near the Current Tape PositionWatching Playback on a Basic Operations PlaybackPress the Menu button Using the Menu ScreensTo turn off the menu screen ExampleTypes Displaying Recording GuideGU I DE Turning on the recording guideSelect OFF in above Setting the Digital ZoomTo use optical zoom only Press lor mto select 40 or 300, then press the SET buttonGamma Brightness Compensation Useful features Camera RecordingTo cancel Gamma Brightness Compen- sation To obtain a brighter pictureGain-up To cancel the gain-up functionPress the GAMMA/BRIGHTER button again Eindicator appears Fade In and Fade Out UsingTo cancel Fade mode To use Fade Out onlyRecording Standby Quick ReturnEdit Search Mode, press and holdAttaching the Supplied Tripod Adapter To cancel the still imageStill Recording on Tape To pause recordingDigital Image Stabilization DIS To cancel DIS functionWide Screen To return to normal screenSelf Recording More Information on Self Re- cordingAP E SP E E D LP Recording in LP Long Play Recording ModeTo return to SP mode Press l or m to select LP, then press the SET buttonPress l or m to select 16bit, then press the SET button Selecting the 16-bit Audio Recording ModeTo return to 12-bit audio recording mode Select 12bit in aboveRemo T E on Using the Remote ControlInstalling the Batteries ActivatingSlow Useful Features PlaybackDisplaying the Date and Time of Recording S P L AYCopying an Image from Tape to Card To cancel Gamma PlaybackGamma Playback Gamma Playback has no effect during still playbackPress l or m to select the desired To cancel Picture Effect PlaybackPicture Effect Playback Picture effect, then press the SETTo return to Auto Focus mode Manual FocusManual Exposure Advanced Features Camera RecordingTo return to Auto Exposure mode Screen is displayedWhite Balance Lock Setting the Camcorder to Full Auto modeTo return to Auto White Balance mode To cancel the digital picture effect Digital Picture EffectsScene Menu Program AE To cancel the scene settingScene settings cannot be used when displaying a still image SC E NE Menu SportDisplay format Using the Time CodeOU T Displaying the time code on a TV during playbackTo stop editing EditingCutting Unwanted Sequences RecordingTo Record from an External Source Advanced Features PlaybackRecording from an External Source To stop recordingTo DV terminal Using the Camcorder as a ConverterL G D G T L O N Digital equipmentTo Record from Video Equip Editing with the DVTerminal IEEE1394 MentYou can select any of the following audio playback modes Selecting the Audio Playback ModeAUD I O Audio Dubbing mode Audio Dubbing FeatureNormal recording mode Audio RecordingTo pause audio dubbing To cancel audio dubbingAudio Dubbing Press the Menu button. The audio dubbing screen disappearsPress the Still button fully to begin recording Picture quality Approx. number Setting Selecting the Picture QualityRecording with the Self TimerDigital Still Camera Features Card Recording Formatting a Card Press j, k, l or m on the Operation Card PlaybackAvailable Operations during Full-screen Display Button to move the selection frame toTo cancel the protection set- ting Delete ProtectionDeleting One Stored Image Digital Still Camera Features PlaybackDeleting Stored Images Press j, k, l or m to select the image to be deletedDeleting All Stored Images Assigning Print Order to an Image Print OrderAbout Dpof Assigning Print Order to All Images To cancel the print order for an imageTo cancel the print order for all images Card to Computer Installing the USB driverTransferring Data on System RequirementsWindows ME Disconnecting the USB cableImage Folders and File Names Windows XPPress l or m to select Slide Show Slide Show PlaybackTo stop Slide Show Playback Adjusting the Backlight Picture/Backlight AdjustmentsAdjusting the Picture Press l or m to select OFF, then press the SET button Turning off Confirmation SoundAppendix Hints for Better Shooting Use a wide-angle setting for fast-moving subjectsUseful Information LightingDV and conventional video cassette tapes Appendix DV TechnologySD Memory Card MultiMediaCard Copyright Protection Precautions when using a Mini DV cassette Mini DV Cassette To protect recordings against acciden- tal erasureWatch out for static electricity Precautions on handling MultiMediaCardsAppendix MultiMediaCard Watch out for condensationReplacing the Fluorescent Lamp Precautions on handling SD Memory CardsSD Memory Card AC Adapter Protecting your dataCharging Appendix Battery PackThis camcorder uses a lithium-ion type battery pack StorageCleaning Using Your Camcorder Abroad AC Adapter Supplied AccessoryCancelling Demo Mode Demonstration ModeDemo Mode of F EMO MOD E onBefore Requesting Service PowerCard Camcorder SpecificationsSpecifications are subject to change without notice AC Adapter UADP-0342TAZZ