3Com iCV-08, iCV-01a, iCV-03a user manual Patrol Settings

Page 19

Chapter 3: Web Interface

Choose Yes and WebCAM will increase the lighting of the image. This is useful when monitoring indoors.

Choose No if you do not want WebCAM to compensate for bright indoor lighting and view the images as is.

Color

Choose Yes for color and No for black and white display. Black and White display results in slightly faster FPS (Frames Per Second) video.

Camera Position

Use this option to right the image when WebCAM is installed on the ceiling or wall. Select either; 0 degree (upright), 90, 180 (upside down), or 270 degree.

Pan Control

Use this function to reverse the Pan direction.

Tilt Control

Use this function to reverse the Tilt controls, if necessary.

Note:

Always click Apply to save any changes made. Otherwise, the changes will be lost.

2.3.2 Patrol Settings

This option is only available if a CM03a USB PanTilt Camera is used. Otherwise the function remains hidden.

i.Patrol Setting

WebCAM - user manual

-16-

Image 19

Contents ICV-01a / iCV-03a / iCV-08 WebCAMContents Page Introduction FeaturesPackage Contents WebCAM Front and Back view Step Hardware InstallationIntroduction Web InterfaceView Video Information Basic Settings Advanced Settings Using the Web InterfaceTo View Video Using ActiveX ControlsWeb Interface Web Interface Using Sun Java Controls Web Interface Ii. Network Status InformationSystem Status System InformationEvent Log Current ConnectionsWebCAM Event Log Operator privilege Camera Settings Basic SettingsPatrol Settings Format HotSpot SettingsBoundary Auto PatrollingNetwork Http Port Number Primary DNS Server IPSecondary DNS Server IP Iv. Port NumberWebCAM Default Dynamic DNS Use Default Domain NameRegistration complete. Account details shown as follows Ii. Other Dynamic DNS Service ProviderLogin Name Login PasswordIii. PPPoE Account SettingsWhen Connection should be made Use Public IP to registerIP Filter PasswordUser Name PermissionBlocked IP List Ii. Block IP addressEvent Notification Advanced SettingsEvents RecipientsWeb Interface Event Notification Camera a Motion Detected Always On or EnableMotion Detection Camera a or Camera BSchedule Detection SensitivitySend image every … seconds Stop sending after … emails or image idle for … secondsRecipient Loop from … to …Digits … Email Server …Send to FTP Server & Send Email Image RecordingBegin End hhmm Send image every … minutesEmail of Image Recorded Mail / FTPFTP Server FTP SettingsIi. Email Settings Email Server Requires AuthenticationSending a test mail Iii. Sending Test MailIv. Email Address Book System SettingsSystem Time System Time UpdatesTime Server System Time yyyy/mm/dd hhmmss Iii. LED SettingsIv. Snmp Settings Time Zone Relative to GMTImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Interface Language LanguageIi. Email Preference Reset to factory default Ii. Save / Restore SettingsSave Current Configuration Restore Previous ConfigurationView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Installation Using the UtilityClick on Setup Wizard Setup WizardBasic Settings Account Settings Use the following IP Address Obtain an IP address by DhcpSelect Enable PPPoE connection Obtain an IP address by BootpUsing the Utility Program Launch WebCAM Using the Utility Program IP Address IP ConfigurationDevice Password when accessing from Utility Advanced for password and Http configurationIi. Management Protocol Click IP ConfigurationRefresh Upgrade FirmwareUser can do a manual search by clicking the Refresh MultiMonitor Installing MultiMonitorMultiMonitor MultiMonitor Device Image Server Port Access by WebCAM Address Host Address Remote PortAccess by Image Server Image Server Address User PasswordMultiMonitor Camera Rotation Display the current Camera settings Camera SelectAccount Image ZoomSensitivity Display the Motion Detection Settings Enable MotionWhen Motion DetectPath CompressionConfigure Settings for Email Notification Using Snmp to update network ports Snmp SettingsProtocol MultiMonitor MultiMonitor MultiMonitor System ViewUser Change Password …Account Management… Add User… HelpPermission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Port Forwarding for WebCAM Appendix a Router ConfigurationSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 2 Using the Utility software Appendix B Methods to Update WebCAM FirmwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix D Glossary