3Com iCV-08 Detection Sensitivity, Send image every … seconds, Schedule, Send to FTP Server

Page 34

Chapter 3: Web Interface

Note:

Check that you have setup valid Email / FTP accounts first before proceeding with the rest of the configuration.

To setup Email / FTP, see Section 2.4.4

Detection Sensitivity

This will determines the level of change before motion capture is triggered. A high percentage means a small change will trigger motion capture.

Send image every … second(s)

Select either; 0.5, 1, 2, 3, 4 or 5 seconds.

Stop sending after … email(s) or image idle for … second(s)

WebCAM will stop sending emails on the lower of the two conditions. The Administrator can set between 1, 3, 5, 7 and 10 seconds. Emails can be set from 1 to 99999 pieces or 0 for stop sending email only when image idle occurred.

Schedule

When the unit is set to On Schedule, the Administrator can configure the four preferred schedule time slots for motion detection. Time must be entered in 24hr format.

Send to FTP Server

Click Yes to activate. This option allows the administrator to send and store the motion detected images on a FTP site. This is useful for future reference and recording purpose.

ftp://<empty>/<folder>

This allows the Administrator to determine the folder where the Motion Detected files are stored. Enter a folder name in <folder>. Click Apply when done.

Note:

The folder name must be valid and has appropriate upload permissions.

You must first enter a valid FTP address in Email / FTP page. Otherwise the ftp address field will be left <empty>.

To setup the FTP server, see Section 2.4.4

System Defined / User Defined

The administrator can also determine to either have the system automatically assign the filenames for the pictures saved. Or manually assign the filename.

Filename …

Specify a prefix filename for the motion detected JPG images. The default prefix is image_

WebCAM - user manual

-31-

Image 34
Contents WebCAM ICV-01a / iCV-03a / iCV-08Contents Page Features IntroductionPackage Contents WebCAM Front and Back view Hardware Installation StepWeb Interface IntroductionUsing the Web Interface View Video Information Basic Settings Advanced SettingsUsing ActiveX Controls To View VideoWeb Interface Web Interface Using Sun Java Controls Web Interface System Information InformationSystem Status Ii. Network StatusCurrent Connections Event LogWebCAM Event Log Operator privilege Basic Settings Camera SettingsPatrol Settings Auto Patrolling HotSpot SettingsBoundary FormatNetwork Iv. Port Number Primary DNS Server IPSecondary DNS Server IP Http Port NumberUse Default Domain Name WebCAM Default Dynamic DNSRegistration complete. Account details shown as follows Login Password Service ProviderLogin Name Ii. Other Dynamic DNSUse Public IP to register Account SettingsWhen Connection should be made Iii. PPPoEPermission PasswordUser Name IP FilterIi. Block IP address Blocked IP ListAdvanced Settings Event NotificationRecipients EventsWeb Interface Event Notification Camera a Motion Detected Camera a or Camera B EnableMotion Detection Always On orStop sending after … emails or image idle for … seconds Detection SensitivitySend image every … seconds ScheduleEmail Server … Loop from … to …Digits … RecipientSend image every … minutes Image RecordingBegin End hhmm Send to FTP Server & Send EmailMail / FTP Email of Image RecordedEmail Server Requires Authentication FTP SettingsIi. Email Settings FTP ServerIii. Sending Test Mail Sending a test mailSystem Settings Iv. Email Address BookSystem Time System Time UpdatesTime Server Time Zone Relative to GMT Iii. LED SettingsIv. Snmp Settings System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Interface Language LanguageIi. Email Preference Restore Previous Configuration Ii. Save / Restore SettingsSave Current Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Using the Utility InstallationClick on Setup Wizard Setup WizardBasic Settings Account Settings Obtain an IP address by Dhcp Use the following IP AddressObtain an IP address by Bootp Select Enable PPPoE connectionUsing the Utility Program Launch WebCAM Using the Utility Program IP Configuration IP AddressAdvanced for password and Http configuration Device Password when accessing from UtilityClick IP Configuration Ii. Management ProtocolUpgrade Firmware RefreshUser can do a manual search by clicking the Refresh Installing MultiMonitor MultiMonitorMultiMonitor MultiMonitor Device User Password Access by WebCAM Address Host Address Remote PortAccess by Image Server Image Server Address Image Server PortMultiMonitor Image Zoom Display the current Camera settings Camera SelectAccount Camera RotationDetect Display the Motion Detection Settings Enable MotionWhen Motion SensitivityCompression PathConfigure Settings for Email Notification Using Snmp to update network ports Snmp SettingsProtocol MultiMonitor MultiMonitor MultiMonitor View SystemUser Change Password …Account Management… Add User… HelpPermission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for WebCAMSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 2 Using the Utility software Appendix B Methods to Update WebCAM FirmwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix D Glossary Term Definition