3Com iCV-03a, iCV-01a, iCV-08 user manual Compression, Path

Page 71

Chapter 6: MultiMonitor

Image	Choose from the list of available
Compression:	compressions.
	Note: This list is dependent on the Codec
	that is available or already installed on the
	local PC. To record in MPEC-4, make sure
	you install or upgrade to Windows Media
	Player v10.

Recording AVI File Location where the file will be recorded to. By

Path	default, it is recorded to C:\Program
	Files\WebCAM\MultiMonitor.
	Click Browse to change the file location.

Recorded files are save using the following file extension;

avifile[three digit numerical sequence].

Note: Use the Detail View to check the stop time. You can change the display view or add a new folder here.

Stop after idle for: Set the value between 1 to 100 seconds

Send AVI file Send an AVI file via email in the event any

Notification by motion is detected.

Email:

WebCAM - user manual

-68-

Image 71

Contents ICV-01a / iCV-03a / iCV-08 WebCAMContents Page Introduction FeaturesPackage Contents WebCAM Front and Back view Step Hardware InstallationIntroduction Web InterfaceView Video Information Basic Settings Advanced Settings Using the Web InterfaceTo View Video Using ActiveX ControlsWeb Interface Web Interface Using Sun Java Controls Web Interface Ii. Network Status InformationSystem Status System InformationEvent Log Current ConnectionsWebCAM Event Log Operator privilege Camera Settings Basic SettingsPatrol Settings Format HotSpot SettingsBoundary Auto PatrollingNetwork Http Port Number Primary DNS Server IPSecondary DNS Server IP Iv. Port NumberWebCAM Default Dynamic DNS Use Default Domain NameRegistration complete. Account details shown as follows Ii. Other Dynamic DNS Service ProviderLogin Name Login PasswordIii. PPPoE Account SettingsWhen Connection should be made Use Public IP to registerIP Filter PasswordUser Name PermissionBlocked IP List Ii. Block IP addressEvent Notification Advanced SettingsEvents RecipientsWeb Interface Event Notification Camera a Motion Detected Always On or EnableMotion Detection Camera a or Camera BSchedule Detection SensitivitySend image every … seconds Stop sending after … emails or image idle for … secondsRecipient Loop from … to …Digits … Email Server …Send to FTP Server & Send Email Image RecordingBegin End hhmm Send image every … minutesEmail of Image Recorded Mail / FTPFTP Server FTP SettingsIi. Email Settings Email Server Requires AuthenticationSending a test mail Iii. Sending Test MailIv. Email Address Book System SettingsTime Server System Time UpdatesSystem Time System Time yyyy/mm/dd hhmmss Iii. LED SettingsIv. Snmp Settings Time Zone Relative to GMTImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Ii. Email Preference LanguageInterface Language Reset to factory default Ii. Save / Restore SettingsSave Current Configuration Restore Previous ConfigurationView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Installation Using the UtilityBasic Settings Account Settings Setup WizardClick on Setup Wizard Use the following IP Address Obtain an IP address by DhcpSelect Enable PPPoE connection Obtain an IP address by BootpUsing the Utility Program Launch WebCAM Using the Utility Program IP Address IP ConfigurationDevice Password when accessing from Utility Advanced for password and Http configurationIi. Management Protocol Click IP ConfigurationRefresh Upgrade FirmwareUser can do a manual search by clicking the Refresh MultiMonitor Installing MultiMonitorMultiMonitor MultiMonitor Device Image Server Port Access by WebCAM Address Host Address Remote PortAccess by Image Server Image Server Address User PasswordMultiMonitor Camera Rotation Display the current Camera settings Camera SelectAccount Image ZoomSensitivity Display the Motion Detection Settings Enable MotionWhen Motion DetectPath CompressionConfigure Settings for Email Notification Protocol Snmp SettingsUsing Snmp to update network ports MultiMonitor MultiMonitor MultiMonitor System ViewAccount Management… Change Password …User Permission Choose Manager or User HelpAdd User… Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Port Forwarding for WebCAM Appendix a Router ConfigurationSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 1 Through WebCAM Web Appendix B Methods to Update WebCAM FirmwareMethod 2 Using the Utility software Appendix C IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix D Glossary