3Com iCV-08, iCV-01a, iCV-03a user manual Tcp

Page 85

Appendix A: Router Configuration

Belkin (http://www.belkin.com)

F5D6230-3 – Wireless Cable/DSL Gateway Router

1.Log into your router using your router IP.

2.On the main page, select Virtual Server on the left side of the page under the Securit section.

3.Enter the following information on the page:

Line #1:
Private IP:	Type in the camera’s IP address. (Look at WebCAM IP
	Address LCD display for the last 3 digits of the camera’s IP
	address)
Private Port:	80
Type:	TCP
Public Port:	80
Line #2
Private IP:	Type in the camera’s IP address. (Look at WebCAM IP
	Address LCD display for the last 3 digits of the camera’s IP
	address)
Private Port:	9001
Type:	UDP
Public Port:	9001

4.Click Enter to save the settings. WebCAM should now be configured to work with your router and be accessible from the internet.

F5D7230-4 – 54g Wireless DSL/Cable gateway Router

1.Log into your router using your router IP.

2.On the main page, select Firewall on the left side of the page.

3.Under Firewall, select Virtual Servers.

4.Enter the following information on the page:

Line #1
Enable:	Checked in
Description:	WebCAM - Webpage
Internet Port:	80 to 80
Type:	TCP
Private IP address:	Type in the camera’s IP address. (Look on the WebCAM
	Address LCD display for the last 3 digits of the camera’s IP
	address)

WebCAM - user manual

-82-

Image 85

Contents ICV-01a / iCV-03a / iCV-08 WebCAMContents Page Introduction FeaturesPackage Contents WebCAM Front and Back view Step Hardware InstallationIntroduction Web InterfaceView Video Information Basic Settings Advanced Settings Using the Web InterfaceTo View Video Using ActiveX ControlsWeb Interface Web Interface Using Sun Java Controls Web Interface System Status InformationSystem Information Ii. Network StatusEvent Log Current ConnectionsWebCAM Event Log Operator privilege Camera Settings Basic SettingsPatrol Settings Boundary HotSpot SettingsAuto Patrolling FormatNetwork Secondary DNS Server IP Primary DNS Server IPIv. Port Number Http Port NumberWebCAM Default Dynamic DNS Use Default Domain NameRegistration complete. Account details shown as follows Login Name Service ProviderLogin Password Ii. Other Dynamic DNSWhen Connection should be made Account SettingsUse Public IP to register Iii. PPPoEUser Name PasswordPermission IP FilterBlocked IP List Ii. Block IP addressEvent Notification Advanced SettingsEvents RecipientsWeb Interface Event Notification Camera a Motion Detected Motion Detection EnableCamera a or Camera B Always On orSend image every … seconds Detection SensitivityStop sending after … emails or image idle for … seconds ScheduleDigits … Loop from … to …Email Server … RecipientBegin End hhmm Image RecordingSend image every … minutes Send to FTP Server & Send EmailEmail of Image Recorded Mail / FTPIi. Email Settings FTP SettingsEmail Server Requires Authentication FTP ServerSending a test mail Iii. Sending Test MailIv. Email Address Book System SettingsSystem Time System Time UpdatesTime Server Iv. Snmp Settings Iii. LED SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Interface Language LanguageIi. Email Preference Save Current Configuration Ii. Save / Restore SettingsRestore Previous Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Installation Using the UtilityClick on Setup Wizard Setup WizardBasic Settings Account Settings Use the following IP Address Obtain an IP address by DhcpSelect Enable PPPoE connection Obtain an IP address by BootpUsing the Utility Program Launch WebCAM Using the Utility Program IP Address IP ConfigurationDevice Password when accessing from Utility Advanced for password and Http configurationIi. Management Protocol Click IP ConfigurationRefresh Upgrade FirmwareUser can do a manual search by clicking the Refresh MultiMonitor Installing MultiMonitorMultiMonitor MultiMonitor Device Access by Image Server Image Server Address Access by WebCAM Address Host Address Remote PortUser Password Image Server PortMultiMonitor Account Display the current Camera settings Camera SelectImage Zoom Camera RotationWhen Motion Display the Motion Detection Settings Enable MotionDetect SensitivityPath CompressionConfigure Settings for Email Notification Using Snmp to update network ports Snmp SettingsProtocol MultiMonitor MultiMonitor MultiMonitor System ViewUser Change Password …Account Management… Add User… HelpPermission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Port Forwarding for WebCAM Appendix a Router ConfigurationSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 2 Using the Utility software Appendix B Methods to Update WebCAM FirmwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix D Glossary