3Com iCV-08, iCV-01a, iCV-03a user manual Introduction, Features

Page 4

Chapter 1: Introduction

Chapter 1: Introduction

Section 1. Features

WebCAM is a compact stand-alone web-server capable of remote video surveillance. It can be accessed from anywhere in the world via a standard browser by entering the IP Address, account and password. Each system can support two types of USB PC cameras. This can be regular USB camera, or one that has infra-red built-in or even with Pan-Tilt. The server function allows WebCAM to stream video images directly to the Internet without having to go through a computer.

WebCAM features a Windows-based software that allows the user to archive streaming video directly to the viewer’s hard-drive. The same software also allows the user to monitor multiple cameras on one screen.

Features:

•LCD display.

•Built-in Web Server with 32-Bit RISC CPU

•TWO USB Port for USB PC Camera

•Support USB PC Camera with VIMICRO ZC0301 Plus processor built-in

•Support Pan/Tilt and Infrared USB PC Camera (sold separately)

•10/100Mbps Fast Ethernet Network Access

•Support Java-Enabled Web Browser

•LCD display shows; IP address, Subnet Mask and Gateway

•Support Up to 30 Remote Viewers for each camera

•Up to 8 User Accounts and Passwords

•5.3VDC 1A Maximum

•Operating Temperature: 0°C ~ 60°C; Operating Humidity: 10% ~ 90%

•Dimensions: 48mm x 63mm x 21mm

•Weight: 75g

•For Indoor Use. Protective housing required for outdoor use.

•Network Protocol: HTTP, TCP/IP, UDP, SMTP, PPPoE, Dynamic DNS, DNS Client, SNTP, BOOTP, DHCP, FTP, SNMP

•Resolution available: 640x480 (VGA), 352x288 (CIF), 320x240 (QVGA), 176x144 (QCIF), 160x120 (QQVGA).

•Frame Rate: Up to 15fps in 640x480, Up to 20fps in 320 x 240.

•Motion JPEG video stream.

Section 2. WebCAM as a Remote Surveillance System

Once WebCAM is installed, the user can check any of the connected PC cameras using a standard web browser. The user can monitor and control these cameras simply by entering the IP address shown on the LCD into a Browser.

WebCAM - user manual

-1-

Image 4

Contents WebCAM ICV-01a / iCV-03a / iCV-08Contents Page Features IntroductionPackage Contents WebCAM Front and Back view Hardware Installation StepWeb Interface IntroductionUsing the Web Interface View Video Information Basic Settings Advanced SettingsUsing ActiveX Controls To View VideoWeb Interface Web Interface Using Sun Java Controls Web Interface Information System StatusSystem Information Ii. Network StatusCurrent Connections Event LogWebCAM Event Log Operator privilege Basic Settings Camera SettingsPatrol Settings HotSpot Settings BoundaryAuto Patrolling FormatNetwork Primary DNS Server IP Secondary DNS Server IPIv. Port Number Http Port NumberUse Default Domain Name WebCAM Default Dynamic DNSRegistration complete. Account details shown as follows Service Provider Login NameLogin Password Ii. Other Dynamic DNSAccount Settings When Connection should be madeUse Public IP to register Iii. PPPoEPassword User NamePermission IP FilterIi. Block IP address Blocked IP ListAdvanced Settings Event NotificationRecipients EventsWeb Interface Event Notification Camera a Motion Detected Enable Motion DetectionCamera a or Camera B Always On orDetection Sensitivity Send image every … secondsStop sending after … emails or image idle for … seconds ScheduleLoop from … to … Digits …Email Server … RecipientImage Recording Begin End hhmmSend image every … minutes Send to FTP Server & Send EmailMail / FTP Email of Image RecordedFTP Settings Ii. Email SettingsEmail Server Requires Authentication FTP ServerIii. Sending Test Mail Sending a test mailSystem Settings Iv. Email Address BookSystem Time System Time UpdatesTime Server Iii. LED Settings Iv. Snmp SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Interface Language LanguageIi. Email Preference Ii. Save / Restore Settings Save Current ConfigurationRestore Previous Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Using the Utility InstallationClick on Setup Wizard Setup WizardBasic Settings Account Settings Obtain an IP address by Dhcp Use the following IP AddressObtain an IP address by Bootp Select Enable PPPoE connectionUsing the Utility Program Launch WebCAM Using the Utility Program IP Configuration IP AddressAdvanced for password and Http configuration Device Password when accessing from UtilityClick IP Configuration Ii. Management ProtocolUpgrade Firmware RefreshUser can do a manual search by clicking the Refresh Installing MultiMonitor MultiMonitorMultiMonitor MultiMonitor Device Access by WebCAM Address Host Address Remote Port Access by Image Server Image Server AddressUser Password Image Server PortMultiMonitor Display the current Camera settings Camera Select AccountImage Zoom Camera RotationDisplay the Motion Detection Settings Enable Motion When MotionDetect SensitivityCompression PathConfigure Settings for Email Notification Using Snmp to update network ports Snmp SettingsProtocol MultiMonitor MultiMonitor MultiMonitor View SystemUser Change Password …Account Management… Add User… HelpPermission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for WebCAMSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 2 Using the Utility software Appendix B Methods to Update WebCAM FirmwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix D Glossary Term Definition