3Com iCV-01a, iCV-08, iCV-03a Image Recording, Begin End hhmm, Send image every … minutes

Page 36

Chapter 3: Web Interface

To remove a recipient from the list, click >

To remove all the recipients from the list, click >>

Click Apply to confirm and save the settings.

2.4.3 Image Recording

Image recording allows the user to receive a string of JPG images to either their email account or FTP account. The images will be sent over a predetermined interval.

i.Camera A (or Camera B)

Fig.33 Image Recording webpage

Enable

Click Yes to activate this feature.

Begin – End (hh:mm)

The Administrator can determine up to 2 different time slots for Image Recording. The time is in 24hrs format.

Send image every … minute(s)”

The Administrator can determine the interval (between 1 to 99 minutes) at which WebCAM capture and send an image.

Send to FTP Server & Send Email

This is similar to the function available in Motion Detection page. Please refer to section 2.4.2 above for details.

Note:

The image size received by email / FTP from depends on the resolution set in Basic

Settings Camera Settings Image Size

WebCAM - user manual

-33-

Page 35 Page 37
Image 36
Page 35 Page 37
Contents WebCAM ICV-01a / iCV-03a / iCV-08Contents Page Features IntroductionPackage Contents WebCAM Front and Back view Hardware Installation StepWeb Interface IntroductionUsing the Web Interface View Video Information Basic Settings Advanced SettingsUsing ActiveX Controls To View VideoWeb Interface Web Interface Using Sun Java Controls Web Interface Information System StatusSystem Information Ii. Network StatusCurrent Connections Event LogWebCAM Event Log Operator privilege Basic Settings Camera SettingsPatrol Settings HotSpot Settings BoundaryAuto Patrolling FormatNetwork Primary DNS Server IP Secondary DNS Server IPIv. Port Number Http Port NumberUse Default Domain Name WebCAM Default Dynamic DNSRegistration complete. Account details shown as follows Service Provider Login NameLogin Password Ii. Other Dynamic DNSAccount Settings When Connection should be madeUse Public IP to register Iii. PPPoEPassword User NamePermission IP FilterIi. Block IP address Blocked IP ListAdvanced Settings Event NotificationRecipients EventsWeb Interface Event Notification Camera a Motion Detected Enable Motion DetectionCamera a or Camera B Always On orDetection Sensitivity Send image every … secondsStop sending after … emails or image idle for … seconds ScheduleLoop from … to … Digits …Email Server … RecipientImage Recording Begin End hhmmSend image every … minutes Send to FTP Server & Send EmailMail / FTP Email of Image RecordedFTP Settings Ii. Email SettingsEmail Server Requires Authentication FTP ServerIii. Sending Test Mail Sending a test mailSystem Settings Iv. Email Address BookSystem Time Updates System TimeTime Server Iii. LED Settings Iv. Snmp SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Language Interface LanguageIi. Email Preference Ii. Save / Restore Settings Save Current ConfigurationRestore Previous Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Using the Utility InstallationSetup Wizard Click on Setup WizardBasic Settings Account Settings Obtain an IP address by Dhcp Use the following IP AddressObtain an IP address by Bootp Select Enable PPPoE connectionUsing the Utility Program Launch WebCAM Using the Utility Program IP Configuration IP AddressAdvanced for password and Http configuration Device Password when accessing from UtilityClick IP Configuration Ii. Management ProtocolUpgrade Firmware RefreshUser can do a manual search by clicking the Refresh Installing MultiMonitor MultiMonitorMultiMonitor MultiMonitor Device Access by WebCAM Address Host Address Remote Port Access by Image Server Image Server AddressUser Password Image Server PortMultiMonitor Display the current Camera settings Camera Select AccountImage Zoom Camera RotationDisplay the Motion Detection Settings Enable Motion When MotionDetect SensitivityCompression PathConfigure Settings for Email Notification Snmp Settings Using Snmp to update network portsProtocol MultiMonitor MultiMonitor MultiMonitor View SystemChange Password … UserAccount Management… Help Add User…Permission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for WebCAMSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B Methods to Update WebCAM Firmware Method 2 Using the Utility softwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix D Glossary Term Definition
Top Page Image Contents