3Com iCV-08, iCV-01a, iCV-03a user manual Upgrade Firmware, Refresh

Page 61

Chapter 5: Using the Utility Program

Example:

If a value of say, 8080 is set as the HTTP port number, then enter http://192.168.0.177:8080 in order to access WebCAM web interface.

Uncheck to disable this function.

2.5 Upgrade Firmware

Click this to bring up the upgrade firmware dialog box.

To check the internet for the latest firmware, click Next

Otherwise, check Upgrade the firmware with file saved on the local hard drive.

Click Browse to choose the location where the *.bin file is located.

2.6 About

Click this button to show the software and version details.

Fig.60 About Utility

2.7 Refresh

Utility will automatically search for any WebCAM IP cameras that are connected in the same LAN. It will periodically refresh this list to show the latest status.

WebCAM - user manual

-58-

Image 61

Contents ICV-01a / iCV-03a / iCV-08 WebCAMContents Page Introduction FeaturesPackage Contents WebCAM Front and Back view Step Hardware InstallationIntroduction Web InterfaceView Video Information Basic Settings Advanced Settings Using the Web InterfaceTo View Video Using ActiveX ControlsWeb Interface Web Interface Using Sun Java Controls Web Interface System Status InformationSystem Information Ii. Network StatusEvent Log Current ConnectionsWebCAM Event Log Operator privilege Camera Settings Basic SettingsPatrol Settings Boundary HotSpot SettingsAuto Patrolling FormatNetwork Secondary DNS Server IP Primary DNS Server IPIv. Port Number Http Port NumberWebCAM Default Dynamic DNS Use Default Domain NameRegistration complete. Account details shown as follows Login Name Service ProviderLogin Password Ii. Other Dynamic DNSWhen Connection should be made Account SettingsUse Public IP to register Iii. PPPoEUser Name PasswordPermission IP FilterBlocked IP List Ii. Block IP addressEvent Notification Advanced SettingsEvents RecipientsWeb Interface Event Notification Camera a Motion Detected Motion Detection EnableCamera a or Camera B Always On orSend image every … seconds Detection SensitivityStop sending after … emails or image idle for … seconds ScheduleDigits … Loop from … to …Email Server … RecipientBegin End hhmm Image RecordingSend image every … minutes Send to FTP Server & Send EmailEmail of Image Recorded Mail / FTPIi. Email Settings FTP SettingsEmail Server Requires Authentication FTP ServerSending a test mail Iii. Sending Test MailIv. Email Address Book System SettingsSystem Time System Time UpdatesTime Server Iv. Snmp Settings Iii. LED SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Interface Language LanguageIi. Email Preference Save Current Configuration Ii. Save / Restore SettingsRestore Previous Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Installation Using the UtilityClick on Setup Wizard Setup WizardBasic Settings Account Settings Use the following IP Address Obtain an IP address by DhcpSelect Enable PPPoE connection Obtain an IP address by BootpUsing the Utility Program Launch WebCAM Using the Utility Program IP Address IP ConfigurationDevice Password when accessing from Utility Advanced for password and Http configurationIi. Management Protocol Click IP ConfigurationRefresh Upgrade FirmwareUser can do a manual search by clicking the Refresh MultiMonitor Installing MultiMonitorMultiMonitor MultiMonitor Device Access by Image Server Image Server Address Access by WebCAM Address Host Address Remote PortUser Password Image Server PortMultiMonitor Account Display the current Camera settings Camera SelectImage Zoom Camera RotationWhen Motion Display the Motion Detection Settings Enable MotionDetect SensitivityPath CompressionConfigure Settings for Email Notification Using Snmp to update network ports Snmp SettingsProtocol MultiMonitor MultiMonitor MultiMonitor System ViewUser Change Password …Account Management… Add User… HelpPermission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Port Forwarding for WebCAM Appendix a Router ConfigurationSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 2 Using the Utility software Appendix B Methods to Update WebCAM FirmwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix D Glossary