3Com iCV-03a, iCV-01a FTP Settings, FTP Server, Account Name, Ii. Email Settings, Mail Server

Page 38

Chapter 3: Web Interface

i.FTP Settings

Fig.36 FTP settings

FTP Server

The Administrator will have to enter the full FTP server address here.

Account Name

Enter the FTP login account name here.

Password

Enter the account password. Click Apply to save the above settings.

ii.Email Settings

Fig.37 Email settings

E-mail Server

The Administrator will have to enter the Email server address here.

Note:

Email function can only work using standard Email Server and not Web based Email Server, such as yahoo.com

Sender’s Email Address

Enter a valid email address where the Email will be sent from. Enter the full email address, example: image@asus.com

Email Server Requires Authentication

Select Yes to enter the Account name and Password field below.

Account Name

Enter the full account name, example; image@asus.com.

Note:

In most cases, Sender’s Email Address and Account Name field is the same.

Password

Enter the password for the above account name. Click Apply to save the changes.

WebCAM - user manual

-35-

Image 38
Contents WebCAM ICV-01a / iCV-03a / iCV-08Contents Page Features IntroductionPackage Contents WebCAM Front and Back view Hardware Installation StepWeb Interface IntroductionUsing the Web Interface View Video Information Basic Settings Advanced SettingsUsing ActiveX Controls To View VideoWeb Interface Web Interface Using Sun Java Controls Web Interface System Information InformationSystem Status Ii. Network StatusCurrent Connections Event LogWebCAM Event Log Operator privilege Basic Settings Camera SettingsPatrol Settings Auto Patrolling HotSpot SettingsBoundary FormatNetwork Iv. Port Number Primary DNS Server IPSecondary DNS Server IP Http Port NumberUse Default Domain Name WebCAM Default Dynamic DNSRegistration complete. Account details shown as follows Login Password Service ProviderLogin Name Ii. Other Dynamic DNSUse Public IP to register Account SettingsWhen Connection should be made Iii. PPPoEPermission PasswordUser Name IP FilterIi. Block IP address Blocked IP ListAdvanced Settings Event NotificationRecipients EventsWeb Interface Event Notification Camera a Motion Detected Camera a or Camera B EnableMotion Detection Always On orStop sending after … emails or image idle for … seconds Detection SensitivitySend image every … seconds ScheduleEmail Server … Loop from … to …Digits … RecipientSend image every … minutes Image RecordingBegin End hhmm Send to FTP Server & Send EmailMail / FTP Email of Image RecordedEmail Server Requires Authentication FTP SettingsIi. Email Settings FTP ServerIii. Sending Test Mail Sending a test mailSystem Settings Iv. Email Address BookTime Server System Time UpdatesSystem Time Time Zone Relative to GMT Iii. LED SettingsIv. Snmp Settings System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Ii. Email Preference LanguageInterface Language Restore Previous Configuration Ii. Save / Restore SettingsSave Current Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Using the Utility InstallationBasic Settings Account Settings Setup WizardClick on Setup Wizard Obtain an IP address by Dhcp Use the following IP AddressObtain an IP address by Bootp Select Enable PPPoE connectionUsing the Utility Program Launch WebCAM Using the Utility Program IP Configuration IP AddressAdvanced for password and Http configuration Device Password when accessing from UtilityClick IP Configuration Ii. Management ProtocolUpgrade Firmware RefreshUser can do a manual search by clicking the Refresh Installing MultiMonitor MultiMonitorMultiMonitor MultiMonitor Device User Password Access by WebCAM Address Host Address Remote PortAccess by Image Server Image Server Address Image Server PortMultiMonitor Image Zoom Display the current Camera settings Camera SelectAccount Camera RotationDetect Display the Motion Detection Settings Enable MotionWhen Motion SensitivityCompression PathConfigure Settings for Email Notification Protocol Snmp SettingsUsing Snmp to update network ports MultiMonitor MultiMonitor MultiMonitor View SystemAccount Management… Change Password …User Permission Choose Manager or User HelpAdd User… Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for WebCAMSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 1 Through WebCAM Web Appendix B Methods to Update WebCAM FirmwareMethod 2 Using the Utility software Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix D Glossary Term Definition