3Com iCV-03a, iCV-01a, iCV-08 user manual HotSpot Settings, Boundary, Auto Patrolling, Format

Page 20

Chapter 3: Web Interface

This section allows the user to define hotspots, required patrol boundary, and see where the current camera position.

Show ful Pan Tilt range.

Click to select which camera to control.

User defined hot spot bubble.

Maximum boundary (x,y) of the Pan Tilt camera

Current camera position and view area.

User defined Pan Tilt boundary

Fig.15 WebCAM Patrol Setting / Controls

HotSpot Settings

This part shows the hotspot coordinates and the Administrator can give each location a name. Click and hold on the Hotspot bubble in the above patrol control to re-define the coordinates.

Enter a name for the selected hotspot

Patrol Setting

Enter a name for the selected hotspot

Boundary

This defines the camera patrol boundary. Click and hold on either one of the two boundary bubble to redefine the boundary.

Auto Patrolling

Select Yes to start auto patrolling function.

Select No to stop the patrolling function.

Format

Choose from 5 different patrolling formats;

a.Oscillating – The camera will pan and tilt at the same time within the user defined boundary. Camera will oscillate from left to right and back.

WebCAM - user manual

-17-

Image 20

Contents WebCAM ICV-01a / iCV-03a / iCV-08Contents Page Features IntroductionPackage Contents WebCAM Front and Back view Hardware Installation StepWeb Interface IntroductionUsing the Web Interface View Video Information Basic Settings Advanced SettingsUsing ActiveX Controls To View VideoWeb Interface Web Interface Using Sun Java Controls Web Interface Information System StatusSystem Information Ii. Network StatusCurrent Connections Event LogWebCAM Event Log Operator privilege Basic Settings Camera SettingsPatrol Settings HotSpot Settings BoundaryAuto Patrolling FormatNetwork Primary DNS Server IP Secondary DNS Server IPIv. Port Number Http Port NumberUse Default Domain Name WebCAM Default Dynamic DNSRegistration complete. Account details shown as follows Service Provider Login NameLogin Password Ii. Other Dynamic DNSAccount Settings When Connection should be madeUse Public IP to register Iii. PPPoEPassword User NamePermission IP FilterIi. Block IP address Blocked IP ListAdvanced Settings Event NotificationRecipients EventsWeb Interface Event Notification Camera a Motion Detected Enable Motion DetectionCamera a or Camera B Always On orDetection Sensitivity Send image every … secondsStop sending after … emails or image idle for … seconds ScheduleLoop from … to … Digits …Email Server … RecipientImage Recording Begin End hhmmSend image every … minutes Send to FTP Server & Send EmailMail / FTP Email of Image RecordedFTP Settings Ii. Email SettingsEmail Server Requires Authentication FTP ServerIii. Sending Test Mail Sending a test mailSystem Settings Iv. Email Address BookTime Server System Time UpdatesSystem Time Iii. LED Settings Iv. Snmp SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Ii. Email Preference LanguageInterface Language Ii. Save / Restore Settings Save Current ConfigurationRestore Previous Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Using the Utility InstallationBasic Settings Account Settings Setup WizardClick on Setup Wizard Obtain an IP address by Dhcp Use the following IP AddressObtain an IP address by Bootp Select Enable PPPoE connectionUsing the Utility Program Launch WebCAM Using the Utility Program IP Configuration IP AddressAdvanced for password and Http configuration Device Password when accessing from UtilityClick IP Configuration Ii. Management ProtocolUpgrade Firmware RefreshUser can do a manual search by clicking the Refresh Installing MultiMonitor MultiMonitorMultiMonitor MultiMonitor Device Access by WebCAM Address Host Address Remote Port Access by Image Server Image Server AddressUser Password Image Server PortMultiMonitor Display the current Camera settings Camera Select AccountImage Zoom Camera RotationDisplay the Motion Detection Settings Enable Motion When MotionDetect SensitivityCompression PathConfigure Settings for Email Notification Protocol Snmp SettingsUsing Snmp to update network ports MultiMonitor MultiMonitor MultiMonitor View SystemAccount Management… Change Password …User Permission Choose Manager or User HelpAdd User… Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for WebCAMSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 1 Through WebCAM Web Appendix B Methods to Update WebCAM FirmwareMethod 2 Using the Utility software Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix D Glossary Term Definition