3Com iCV-03a, iCV-01a Account Settings, Use Public IP to register, Iii. PPPoE, User Account

Page 26

Chapter 3: Web Interface

Use Public IP to register

Choose Yes to ensure that WebCAM uses the WAN / Public IP to register with the selected DDNS server.

iii.PPPoE

Use this option to allow WebCAM to connect to the internet directly using your xDSL modem. Once set-up, WebCAM will connect directly to the Internet without going through a router. The LCD will display the current WAN / Public IP instead of the LAN IP Address.

Fig.22 WebCAM PPPoE setting

When Connection should be made

Disabled	:	Default setting.
Connect always	:	WebCAM will automatically dial up and maintain
		continuous connection.

Login Name

Enter the login name assigned by your ISP.

Login Password

Enter the password assigned by your ISP.

2.3.3 Account Settings

This webpage allows you to set up to Eight (8) different user accounts with different access permission level to WebCAM. This section can only be edited by an administrator.

i.User Account

Fig.23 User Account Settings

WebCAM - user manual

-23-

Image 26

Contents WebCAM ICV-01a / iCV-03a / iCV-08Contents Page Features IntroductionPackage Contents WebCAM Front and Back view Hardware Installation StepWeb Interface IntroductionUsing the Web Interface View Video Information Basic Settings Advanced SettingsUsing ActiveX Controls To View VideoWeb Interface Web Interface Using Sun Java Controls Web Interface System Information InformationSystem Status Ii. Network StatusCurrent Connections Event LogWebCAM Event Log Operator privilege Basic Settings Camera SettingsPatrol Settings Auto Patrolling HotSpot SettingsBoundary FormatNetwork Iv. Port Number Primary DNS Server IPSecondary DNS Server IP Http Port NumberUse Default Domain Name WebCAM Default Dynamic DNSRegistration complete. Account details shown as follows Login Password Service ProviderLogin Name Ii. Other Dynamic DNSUse Public IP to register Account SettingsWhen Connection should be made Iii. PPPoEPermission PasswordUser Name IP FilterIi. Block IP address Blocked IP ListAdvanced Settings Event NotificationRecipients EventsWeb Interface Event Notification Camera a Motion Detected Camera a or Camera B EnableMotion Detection Always On orStop sending after … emails or image idle for … seconds Detection SensitivitySend image every … seconds ScheduleEmail Server … Loop from … to …Digits … RecipientSend image every … minutes Image RecordingBegin End hhmm Send to FTP Server & Send EmailMail / FTP Email of Image RecordedEmail Server Requires Authentication FTP SettingsIi. Email Settings FTP ServerIii. Sending Test Mail Sending a test mailSystem Settings Iv. Email Address BookTime Server System Time UpdatesSystem Time Time Zone Relative to GMT Iii. LED SettingsIv. Snmp Settings System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Ii. Email Preference LanguageInterface Language Restore Previous Configuration Ii. Save / Restore SettingsSave Current Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Using the Utility InstallationBasic Settings Account Settings Setup WizardClick on Setup Wizard Obtain an IP address by Dhcp Use the following IP AddressObtain an IP address by Bootp Select Enable PPPoE connectionUsing the Utility Program Launch WebCAM Using the Utility Program IP Configuration IP AddressAdvanced for password and Http configuration Device Password when accessing from UtilityClick IP Configuration Ii. Management ProtocolUpgrade Firmware RefreshUser can do a manual search by clicking the Refresh Installing MultiMonitor MultiMonitorMultiMonitor MultiMonitor Device User Password Access by WebCAM Address Host Address Remote PortAccess by Image Server Image Server Address Image Server PortMultiMonitor Image Zoom Display the current Camera settings Camera SelectAccount Camera RotationDetect Display the Motion Detection Settings Enable MotionWhen Motion SensitivityCompression PathConfigure Settings for Email Notification Protocol Snmp SettingsUsing Snmp to update network ports MultiMonitor MultiMonitor MultiMonitor View SystemAccount Management… Change Password …User Permission Choose Manager or User HelpAdd User… Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for WebCAMSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 1 Through WebCAM Web Appendix B Methods to Update WebCAM FirmwareMethod 2 Using the Utility software Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix D Glossary Term Definition