3Com iCV-03a, iCV-01a, iCV-08 user manual Advanced Settings, Event Notification

Page 29

Chapter 3: Web Interface

2.4 Advanced Settings

This section allows the Administrator to set up some of the features available in the server.

2.4.1Event Notification

2.4.2Motion Detection

2.4.3Image Recording

2.4.4Email / FTP

2.4.5System Settings

2.4.6Image Server

2.4.7Language

2.4.8About

2.4.1 Event Notification

This section determines the type of event that will be included if an email notification is sent by WebCAM.

Note:

Administrator privilege is required to configure this section.

i.Event Notification

A total of 8 email recipients can be assigned to receive notification.

Fig.26 WebCAM Event Notification Page

Send Email

Select Yes to activate this feature. Default is No.

Email Server

A valid Email Server, User name and password must be setup for this feature to work. If this has not been setup, click Edit and to go to Email / FTP setup page. (see Section 2.4.4)

Note:

Email function can only work using standard Email Server and not Web based Email Server, such as yahoo.com

Email Address Book

WebCAM - user manual

-26-

Image 29

Contents ICV-01a / iCV-03a / iCV-08 WebCAMContents Page Introduction FeaturesPackage Contents WebCAM Front and Back view Step Hardware InstallationIntroduction Web InterfaceView Video Information Basic Settings Advanced Settings Using the Web InterfaceTo View Video Using ActiveX ControlsWeb Interface Web Interface Using Sun Java Controls Web Interface System Status InformationSystem Information Ii. Network StatusEvent Log Current ConnectionsWebCAM Event Log Operator privilege Camera Settings Basic SettingsPatrol Settings Boundary HotSpot SettingsAuto Patrolling FormatNetwork Secondary DNS Server IP Primary DNS Server IPIv. Port Number Http Port NumberWebCAM Default Dynamic DNS Use Default Domain NameRegistration complete. Account details shown as follows Login Name Service ProviderLogin Password Ii. Other Dynamic DNSWhen Connection should be made Account SettingsUse Public IP to register Iii. PPPoEUser Name PasswordPermission IP FilterBlocked IP List Ii. Block IP addressEvent Notification Advanced SettingsEvents RecipientsWeb Interface Event Notification Camera a Motion Detected Motion Detection EnableCamera a or Camera B Always On orSend image every … seconds Detection SensitivityStop sending after … emails or image idle for … seconds ScheduleDigits … Loop from … to …Email Server … RecipientBegin End hhmm Image RecordingSend image every … minutes Send to FTP Server & Send EmailEmail of Image Recorded Mail / FTPIi. Email Settings FTP SettingsEmail Server Requires Authentication FTP ServerSending a test mail Iii. Sending Test MailIv. Email Address Book System SettingsTime Server System Time UpdatesSystem Time Iv. Snmp Settings Iii. LED SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmssImage Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Ii. Email Preference LanguageInterface Language Save Current Configuration Ii. Save / Restore SettingsRestore Previous Configuration Reset to factory defaultView Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Installation Using the UtilityBasic Settings Account Settings Setup WizardClick on Setup Wizard Use the following IP Address Obtain an IP address by DhcpSelect Enable PPPoE connection Obtain an IP address by BootpUsing the Utility Program Launch WebCAM Using the Utility Program IP Address IP ConfigurationDevice Password when accessing from Utility Advanced for password and Http configurationIi. Management Protocol Click IP ConfigurationRefresh Upgrade FirmwareUser can do a manual search by clicking the Refresh MultiMonitor Installing MultiMonitorMultiMonitor MultiMonitor Device Access by Image Server Image Server Address Access by WebCAM Address Host Address Remote PortUser Password Image Server PortMultiMonitor Account Display the current Camera settings Camera SelectImage Zoom Camera RotationWhen Motion Display the Motion Detection Settings Enable MotionDetect SensitivityPath CompressionConfigure Settings for Email Notification Protocol Snmp SettingsUsing Snmp to update network ports MultiMonitor MultiMonitor MultiMonitor System ViewAccount Management… Change Password …User Permission Choose Manager or User HelpAdd User… Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Port Forwarding for WebCAM Appendix a Router ConfigurationSMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Method 1 Through WebCAM Web Appendix B Methods to Update WebCAM FirmwareMethod 2 Using the Utility software Appendix C IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix D Glossary