Cannon QL Uses of Lenses, Distance Scale, Changing Lenses, Infrared Index " R

Page 18

Uses of Lenses

 

Changing Lenses 

In removing the lens from the camera, after turning the bayonet ring of the lens to the left, take out the lens.

 

In mounting the lens, match the red dot of the lens to the red dot on the camera mount Turn the bayonet ring to the right and fasten.

 

è

 When mounting, turn the bayonet ring of the lens sufficiently to the left and coincide the red dot and guide pin of the lens.

 

è

 Do not change your lens in a strong light. When changing your lenses have the replacement lens at hand. Then quickly change the 

lenses in the shade. . . or use your shadow as a shield from direct light.

 

è

 There is a pre-set aperture lever at the back end of the lens which opens and closes the aperture. When the lens is removed, be sure to 

always put on the dust cap so as to protect the aperture lever.

 

è

 If interchangeable lenses are changed while the CdS actuating lever is in locked position, the pre-set aperture lever cannot be 

connected to the coupling part on the camera body and the pre-set aperture will not function. Be sure to unlock the CdS actuating lever 

when changing interchangeable lenses.

 

è

 Do not touch the panicle mirror or the coupling section of the aperture. When not in use for a long time, protect the panicle mirror by 

putting on the flange cap. 

Distance Scale 

The distance scale indicates the distance between the focused subject and the film plane. The scale is necessary for checking the depth 

of-field, for infrared photography and flash photography.

 

è

 The correct position of the scale, where the distance is a one-digit figure, is in the middle of the figure; if it is a two-digit figure, it is 

between the two figures; and if it is a three-digit figure, it is in the middle of the central figure. 

Infrared Index " R " 

For infrared photography, correction of the distance scale is necessary because the focal position deviates a little from ordinary 

photography. Make ordinary focusing first, then adjust that distance scale to the infrared mark " R ". For instance, if the distance reads 

10m after focusing, merely shift the 10 scale to " R " position. 

è 

The position of " R " is scaled according to the use of the standard of a film with the highest sensitivity of a wave length of about 

800my and infrared filter (for example, KODAK IR 135 film and WRITTEN 87 filter). 

Image 18
Contents Camera Manual Before UsingCanon Pellix To main Chinon/Ricoh manual siteTable of contents Technical Data Technical Data — page 4 Battery Check Mercury Battery Loading :Attaching the Cable Release Safety Device for ShutterFilm Counter Film Winding :Shutter and Aperture Adjustment : Shutter Speed DialLens Aperture Lens with A-M Ring Pre-Set Aperture and Checking of Depth-of-FieldRelation Between the Pellicle Mirror, CdS, Diaphragm and Shutter Lens with Manual Aperture RingHow to Use Built-in Exposure Meter : Film Speed SettingExposure Setting 1--Shutter Speed Priority Method : How to Measure the Average BrightnessCdS Actuating Lever Exposure Setting 2--F Stop Priority Method : Focusing : Holding the Camera : Composition and ViewfinderHolding the Camera : — page 14 Film Loading : Setting the Film Speed Checking Correct Film LoadingFilm Rewinding : Photography Using Self-timer and Eyepiece Shutter : Eyepiece ShutterFlash Synchronization : Distance Scale Uses of Lenses :Changing Lenses Infrared Index " R "Depth of field Scale Lens Mount (FL and R Series Lenses)Film Plane Mark Filters : Double Exposure :Proper Care of the Canon PELLIX QL : Cleaning of the CameraCleaning the Lens Storage of CameraCanon Zoom Lenses Interchangeable Lenses and Accessories :Canon Interchangeable Lenses New "Compact Series" LensesAccessories Technical DataCanon Booster Technical Data — page 24