JVC KY-F1030 manual Combining with a presentation system, Mounting the lens

Page 11

2. Before shooting (continued)

Combining with a presentation system

The image shot by the KY-F1030 can be passed though a scan rate converter and shown on a

D-ILA presenter or SXGA-compliant monitor.

Mounting the lens

Follow the procedure shown below when mounting a motorized lens. For further details, see the instruction manual of the lens and lens remote control.

 

 

AA-P700

 

Connect the power supply

AC ADAPTER AA-P700

 

POWER

 

(  page E18)

 

 

 

ON

 

 

 

AC

 

 

OFF

 

 

AC adapter

[VIDEO IN]

 

[ANALOG OUT]

 

[DC IN]

 

 

 

4.

[MD

Camera head

Thread section

 

Mount clamp ring

 

Lens

 

2.

 

 

 

CAUTION

CONTROL] connector

Perform mounting of the lens

3. Lock

 

with the power of the camera

 

turned OFF. Mounting with the

 

 

 

 

power on could result in dam-

 

 

age.

 

Lens is not included with this

(Female)

4. Lock

unit.

 

FOCUS

LOCK

 

 

Mount the lens (  page E17)

D-ILA or SXGA-compliant monitor

 

JVC KM-F700

[VIDEO INPUT]

 

terminal

Scan rate converter

1.Connect the KY-F1030’s [ANALOG OUT] connector to the scan rate converter’s [VIDEO INPUT] terminal.

2.Connect the AC adapter (AA-P700) to the KY-F1030, and then turn ON the power.

3.Turn ON the other devices.

*Also see the instructions for the scan rate converter to be used.

MEMO

When connected to the PC through the [IEEE1394] connector, or an RS-232C device is connected to the [REMOTE] terminal, the auto white balance function of the scan rate converter will be disabled.

When the shutter speed becomes slower (slower than 1/7.5s), the image may be seen interrupted.

The image will not freeze even when the scan rate converter’s [FREEZE] button is pressed.

The scan rate converter’s [SEND] command is invalid.

 

Lens remote control

 

 

Compatible lens

Lens remote controller

Compatible

remote controller

 

zoom lens

FJINON, RMD-10,

 

D167.3A-D29

RMD-20

 

1.

Remove the lens mount cap. At this time, take caution so that dust do not enter inside the

 

mount.

2.

To mount the lens, lightly press the thread section of the lens mount onto the thread section

 

of KY-F1030, then turn the lens unit or KY-F1030 slowly clockwise until it is securely tight-

 

ened.

 

MEMO

To change the position of the lens rotation:

￿First, turn the mount clamp ring clockwise (1/4 turns) with the lens facing you.

￿Slowly turn the lens and after adjusting the position, retighten the mount clamp ring.

3.

Insert the camera cable of the lens into the [LENS] connection terminal on the rear of KY-

 

F1030, then securely lock.

 

The iris control is made from the KY-F1030.

4.

When using the lens remote controller, connect the lens control cable (female) to the re-

 

mote control. Also, when focusing and zoom controller is to be performed on the KY-F1030,

 

connect the lens control cable (female) to the [MD CONTROL] terminal on the KY-F1030.

 

When operating the lens iris manually by lens remote control connection, set IRIS MODE to

 

manual. (  page E33)

 

CAUTION

When using a motorized lens, use the AC adapter as power supply for the KY-F1030.

If power is supplied via the [IEEE1394] connector, control of the motorized lens is not possible from the

KY-F1030.

E16

E17

Image 11
Contents This instruction book is made from 100% recycled paper Illustration with optional lens attachmentSerious damage to the appliance Important SafeguardsJVC Professional Products Italia S.p.A These instructions are for KY-F1030U Table of Contents Introduction FeaturesAccessories and attachments Front and bottom Part names and their functionsRear Side switch panel section insideAnalog Output terminal D-sub Pin configurations of connectorsIeee 1394 connector MD Control Metal 12-pin, female Lens terminal Metal 12-pin, femaleAC adapter Connecting through digital output connectorConnecting through analog output connector Before shootingMounting the lens Combining with a presentation systemMounting method Connecting powerConnecting the IEEE1394 Cable Mounting the cameraAuto Settings and adjustments for shootingLens settings Lected, then press the SET button White balance adjustmentTemp the text will be displayed in purple when se Error Over Light excessive lightShutter item will return to white Focus adjustmentShooting a computer monitor screen Shooting a PC monitor  When the shutter mode is Random Iris, etc How to use White spot detection EtcE31 Menu screen settingsMenu screen flow Exposure screen Setting procedureScan ShutterStep V.SCAN Random EEI OFF StepProcess screen White Balance screenLens screen Menu Quick screen System Setting screenZoom Resetting menu settingsE45 About ALC and EEI operations SpecificationsOthers Inch screw 125.5120