JVC GR-SXM86ED specifications EN39, For Insert Editing and Audio Dubbing

Page 39

Display

 

e

4

Audio dubbing

M– 0 : 0 5 : 2 0

indicator

During Audio

Dubbing

Remote sensor

EN39

Audio Dubbing

You can record a new soundtrack on a prerecorded tape. The existing original sound is erased and replaced by the sound from the built-in microphone.

Perform steps 1, 2 and 3 of the Insert Editing procedure (pg. 38) before continuing.

NOTE:

Use the remote control unit to perform the following procedures.

1 Press REW (2) to go a little beyond the beginning of the scene onto which you want to dub the new audio, press PLAY (4) to view the recorded tape, then press PAUSE (6) at exactly the point where dubbing should start.

2 Press and hold A. DUB (e), and without releasing A. DUB (e), press and release PAUSE (6). The Audio Dub-Standby mode is engaged.

START/STOP

REW

PLAY

STOP

Microphone

A.DUB

PAUSE

3 To begin Audio Dubbing, press PLAY (4). When the counter reaches “0:00:00”, Audio Dubbing stops automatically and the camcorder enters the Audio Dub-Standby mode.

4 To end Audio Dubbing, press STOP (5).

NOTES:

Do not press FF (3) or REW (2) during Audio Dub- Standby, or the edit points will not be accurate.

If the microphone is too close to the TV, or if the TV’s volume is too high, whistling or howling may occur.

NOTES

(for Insert Editing and Audio Dubbing):

Insert Editing and Audio Dubbing may not work correctly if the tape contains blank segments, or if the recording speed was changed during the original recording.

To edit/dub onto a tape, make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape.

Do not press STOP (5) during Insert Editing or Audio Dubbing, or the edit points will not be accurate.

During Insert Editing and Audio Dubbing, when Insert-Pause or Audio Dub-Standby is engaged, the counter may go slightly past “0:00:00”. Recording, however, stops at exactly 0:00:00.

Image 39
Contents Instructions It is recommended that you Dear CustomerModels equipped with LCD monitor only EN3Automatic Demonstration Power Cord Remote Control Unit RM-V716U Battery PackEN5 How To Attach The Core FilterSlide Battery Release and pull out the battery pack Charging the Battery PackPower To Detach The Battery PackApproximate recording time unit min Using the Battery PackUsing AC Power EN7Tripod Mounting Grip AdjustmentRotate Menu to select Date/Time SettingsPower lamp Comes on10 EN Recording Format SettingRegular VHS VCR EN11Tape Length Setting Recording Mode SettingEN13 Loading/Unloading a CassetteRotate Bright until the bright level 14 ENShooting While Watching To Stop RecordingEN15 SELF-RECORDINGmodels equipped with LCD monitor onlyJournalistic Shooting models equipped with LCD monitor only 16 EN ZoomZoom Out Press the Recording Start/Stop Button to start recording EN17If you press during Record-Standby 18 ENSnapshot Night-ScopeFade/Wipe Effects EN19Fades in/out to a black screen Program AE With Special Effects 20 ENEN21 Digital EffectsIf you select Jlip ID no Using Menus For Detailed AdjustmentMenu Screen Explanations Camera MenuSystem Menu 24 EN Instant Titles Date/Time InsertSet REC Time and 2 of Animation above Time-LapseSet the Power Switch to Press MENU. The Menu Screen appears Exposure ControlEN27 Manual Focus Focusing28 EN Auto FocusPress Menu again to close the Menu Screen White Balance AdjustmentManual White Balance Operation EN2930 EN Load a tape pg Set the Power Switch toEN31 To cancel the effect, select OFF in stepUse the provided A/V cable Use the provided A/V cable and S-Video cableEN33 Power supply instead of the battery pack pgBasic Connections Tape DubbingSlide the latch to open the adapter compartment 34 ENCassette Adapter CoverFunctions Buttons EN35EN Using the Remote Control Unit To End Zoom EN37Playback Zoom Press Play to find the scene of interestInsert Editing 38 ENAudio Dubbing EN39For Insert Editing and Audio Dubbing You are now ready to try Random Assemble Editing 40 ENSET REMOTE/VCR Code Press Shift for this oneConnect the editing cable to the Remote Pause terminal Connect the editing cable to the R.A.EDIT connectorEN41 Make ConnectionsSelect Scenes 42 ENEditing cable and the A/V cable OUT 9 the scene you want to edit and press PauseDate/Time SettingsCharging time varies according to the ambient temperature 44 ENTime Base TBC indicator turns green grey with a camcorder equippedRecording TBCAnimation or Time-Lapse is not No power is suppliedRecording cannot be performed Recording does not startLens CAP warning indicator An error number i.e. E03 appearsThat Date/Time setting is carried out Lens CAP warning indicator may blink when3 4 5 y u # $ % 48ENEN49 Indications During Recording Night-Scope Indicator ................... pgVHS/S-VHS ET Recording Indicator 50 ENIndications Function Tape Counter Tape Running Indicator PlaybackIndications During Playback EN51To avoid hazard To prevent damage and prolong service life52 EN Use only the following batteriesEN53 About moisture condensation To prolong service lifeCleaning The Camcorder To prevent damage to the LCD monitor, do notConnectors Optional AccessoriesGeneral GR-FX36EDGR-FXM66EDGR-SX56EDGR-SXM76EDGR-SXM85EDGR-SXM86ED