JVC GR-SXM86ED No power is supplied, Recording cannot be performed, Recording does not start

Page 46

46ENTROUBLESHOOTING

If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.); and then re-connect it and proceed as usual from the beginning.

SYMPTOM

POWER

No power is supplied.

POSSIBLE CAUSE(S)

●The battery pack has not been attached correctly (☞ pg. 6).

●The battery pack is not charged (☞ pg. 6).

●The power supply has not been correctly connected (☞ pg. 6, 7).

The power suddenly goes off and does not come back on by itself.

●The battery pack has completely discharged.

●Remove the cassette and disconnect the power source, then after a few minutes, try turning the power back on. If it still does not come on, consult your nearest JVC dealer.

RECORDING

Recording cannot be performed.

● Make sure the Erase Protection tab is in the position that

 

allows recording. If not, slide the tab. Some cassettes have

 

removable tabs. If the tab has been removed, cover the

 

hole with adhesive tape (☞ pg. 13).

 

 

Recording does not start.

● The camcorder Power Switch has not been set to “ ” or

 

“ ” (☞ pg. 14).

 

 

Animation or Time-Lapse is not

● Before recording in the Animation mode at the very

available.

beginning of a tape, set the camcorder to the Recording

 

mode for about 5 seconds, so that the tape runs smoothly.

 

Using the Fade-in function at this point is a good way to

 

begin an animated programme (☞ pg. 26).

 

 

PLAYBACK

 

The tape is running, but there is no

● The TV has not been set to its VIDEO mode or channel.

playback picture.

● If A/V connection is used, the TV’s VIDEO/TV Switch has

 

not been set to VIDEO.

 

 

Playback picture is blurred or

● The video heads are dirty or worn out. Consult your nearest

interrupted.

JVC dealer for head cleaning or replacement.

 

 

The counter indication is blurred

● This is normal.

during Still playback.

 

 

 

TAPE TRANSPORT

 

The tape stops during fast-forward or

● The Counter Memory Function has been activated

rewind.

(☞ pg. 31).

 

 

Rewinding or fast-forwarding cannot

● The tape is already fully wound on one reel or the other.

be performed.

 

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Instructions Dear Customer It is recommended that youEN3 Models equipped with LCD monitor onlyPower Cord Remote Control Unit RM-V716U Battery Pack Automatic DemonstrationHow To Attach The Core Filter EN5To Detach The Battery Pack Charging the Battery PackPower Slide Battery Release and pull out the battery packEN7 Using the Battery PackUsing AC Power Approximate recording time unit minGrip Adjustment Tripod MountingComes on Date/Time SettingsPower lamp Rotate Menu to selectRecording Format Setting 10 ENEN11 Regular VHS VCRRecording Mode Setting Tape Length SettingLoading/Unloading a Cassette EN13To Stop Recording 14 ENShooting While Watching Rotate Bright until the bright levelSELF-RECORDINGmodels equipped with LCD monitor only EN15Journalistic Shooting models equipped with LCD monitor only Zoom 16 ENZoom Out EN17 Press the Recording Start/Stop Button to start recordingNight-Scope 18 ENSnapshot If you press during Record-StandbyEN19 Fade/Wipe EffectsFades in/out to a black screen 20 EN Program AE With Special EffectsDigital Effects EN21Using Menus For Detailed Adjustment If you select Jlip ID noCamera Menu Menu Screen ExplanationsSystem Menu 24 EN Date/Time Insert Instant TitlesTime-Lapse Set REC Time and 2 of Animation aboveExposure Control Set the Power Switch to Press MENU. The Menu Screen appearsEN27 Auto Focus Focusing28 EN Manual FocusEN29 White Balance AdjustmentManual White Balance Operation Press Menu again to close the Menu ScreenLoad a tape pg Set the Power Switch to 30 ENTo cancel the effect, select OFF in step EN31Use the provided A/V cable and S-Video cable Use the provided A/V cableTape Dubbing Power supply instead of the battery pack pgBasic Connections EN33Cover 34 ENCassette Adapter Slide the latch to open the adapter compartmentEN35 Functions ButtonsEN Using the Remote Control Unit Press Play to find the scene of interest EN37Playback Zoom To End Zoom38 EN Insert EditingEN39 Audio DubbingFor Insert Editing and Audio Dubbing Press Shift for this one 40 ENSET REMOTE/VCR Code You are now ready to try Random Assemble EditingMake Connections Connect the editing cable to the R.A.EDIT connectorEN41 Connect the editing cable to the Remote Pause terminal42 EN Select ScenesOUT 9 the scene you want to edit and press Pause Editing cable and the A/V cable44 EN SettingsCharging time varies according to the ambient temperature Date/TimeTBC TBC indicator turns green grey with a camcorder equippedRecording Time BaseRecording does not start No power is suppliedRecording cannot be performed Animation or Time-Lapse is notLens CAP warning indicator may blink when An error number i.e. E03 appearsThat Date/Time setting is carried out Lens CAP warning indicator48EN 3 4 5 y u # $ %EN49 50 EN Night-Scope Indicator ................... pgVHS/S-VHS ET Recording Indicator Indications During RecordingEN51 Tape Counter Tape Running Indicator PlaybackIndications During Playback Indications FunctionUse only the following batteries To prevent damage and prolong service life52 EN To avoid hazardEN53 To prevent damage to the LCD monitor, do not To prolong service lifeCleaning The Camcorder About moisture condensationOptional Accessories ConnectorsGeneral GR-FX36EDGR-FXM66EDGR-SX56EDGR-SXM76EDGR-SXM85EDGR-SXM86ED
Top Page Image Contents