JVC GR-SXM86ED To prevent damage to the LCD monitor, do not, To prolong service life, After Use

Page 54

54ENCAUTIONS(cont.)

LCD Monitor

1.To prevent damage to the LCD monitor, DO NOT . . .

... push it strongly or apply any shocks.

... place the camcorder with the LCD monitor on the bottom.

2.To prolong service life . . .

... avoid rubbing it with coarse cloth.

3.Be aware of the following phenomena for LCD monitor use. These are not malfunctions:

•While using the camcorder, the surface around the LCD monitor and/or the back of the LCD monitor may heat up.

•If you leave power on for a long time, the surface around the LCD monitor becomes hot.

About moisture condensation . . .

●You may have observed that pouring a cold liquid into a glass will cause drops of water to form on the glass’ outer surface. This same phenomenon occurs on the head drum of a camcorder when it is moved from a cool place to a warm place, after heating a cold room, under extremely humid conditions or in a place directly subjected to the cool air from an air conditioner.

●Moisture on the head drum can cause severe damage to the video tape, and can lead to internal damage to the camcorder itself.

Serious malfunctioning

If malfunctioning occurs, stop using the unit immediately and consult your local JVC dealer.

For Your Maintenance

1. After Use

1Set the Power Switch to “OFF” to turn off the camcorder.

2Open the LCD monitor to an angle of over 60 degrees. Slide EJECT to open the cassette holder, then remove the cassette.

3Close and lock the cassette holder by pressing the Close button.

4Close and lock the LCD monitor.

5Slide BATTERY RELEASE to remove the battery pack.

6Attach the provided lens cap to the camcorder’s lens.

2.Cleaning The Camcorder

1 CLEAN EXTERIOR

Wipe gently with a soft cloth.

Put cloth in diluted mild soap and wring it well to wipe off heavy dirt, then wipe again with a dry cloth.

2 CLEAN LCD MONITOR

Open the LCD monitor and wipe it gently with a soft cloth. Be careful not to damage the monitor. Close the LCD monitor.

3 CLEAN LENS

Blow it with a blower brush, then wipe it gently with lens cleaning paper.

4 REMOVE EYEPIECE

Turn the eyepiece counterclockwise and pull it out.

5 CLEAN VIEWFINDER

Remove dust using a blower brush.

6RE-ATTACH EYEPIECE

Re-attach the eyepiece and turn it clockwise.

NOTES:

●Avoid using strong cleaning agents such as benzine or alcohol.

●Cleaning should be done only after the battery pack has been removed or other power units have been disconnected.

●Mould may form if the lens is left dirty.

●When using a cleaner or chemically treated cloth, refer to the cautions that came with it.

●When removing the eyepiece, be sure to hold the viewfinder securely.

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Instructions Dear Customer It is recommended that youEN3 Models equipped with LCD monitor onlyPower Cord Remote Control Unit RM-V716U Battery Pack Automatic DemonstrationHow To Attach The Core Filter EN5To Detach The Battery Pack Charging the Battery PackPower Slide Battery Release and pull out the battery packEN7 Using the Battery PackUsing AC Power Approximate recording time unit minGrip Adjustment Tripod MountingComes on Date/Time SettingsPower lamp Rotate Menu to selectRecording Format Setting 10 ENEN11 Regular VHS VCRRecording Mode Setting Tape Length SettingLoading/Unloading a Cassette EN13To Stop Recording 14 ENShooting While Watching Rotate Bright until the bright levelEN15 SELF-RECORDINGmodels equipped with LCD monitor onlyJournalistic Shooting models equipped with LCD monitor only 16 EN ZoomZoom Out EN17 Press the Recording Start/Stop Button to start recordingNight-Scope 18 ENSnapshot If you press during Record-StandbyFade/Wipe Effects EN19Fades in/out to a black screen 20 EN Program AE With Special EffectsDigital Effects EN21Using Menus For Detailed Adjustment If you select Jlip ID noMenu Screen Explanations Camera MenuSystem Menu 24 EN Date/Time Insert Instant TitlesTime-Lapse Set REC Time and 2 of Animation aboveSet the Power Switch to Press MENU. The Menu Screen appears Exposure ControlEN27 Auto Focus Focusing28 EN Manual FocusEN29 White Balance AdjustmentManual White Balance Operation Press Menu again to close the Menu ScreenLoad a tape pg Set the Power Switch to 30 ENTo cancel the effect, select OFF in step EN31Use the provided A/V cable and S-Video cable Use the provided A/V cableTape Dubbing Power supply instead of the battery pack pgBasic Connections EN33Cover 34 ENCassette Adapter Slide the latch to open the adapter compartmentEN35 Functions ButtonsEN Using the Remote Control Unit Press Play to find the scene of interest EN37Playback Zoom To End Zoom38 EN Insert EditingAudio Dubbing EN39For Insert Editing and Audio Dubbing Press Shift for this one 40 ENSET REMOTE/VCR Code You are now ready to try Random Assemble EditingMake Connections Connect the editing cable to the R.A.EDIT connectorEN41 Connect the editing cable to the Remote Pause terminal42 EN Select ScenesOUT 9 the scene you want to edit and press Pause Editing cable and the A/V cable44 EN SettingsCharging time varies according to the ambient temperature Date/TimeTBC TBC indicator turns green grey with a camcorder equippedRecording Time BaseRecording does not start No power is suppliedRecording cannot be performed Animation or Time-Lapse is notLens CAP warning indicator may blink when An error number i.e. E03 appearsThat Date/Time setting is carried out Lens CAP warning indicator48EN 3 4 5 y u # $ %EN49 50 EN Night-Scope Indicator ................... pgVHS/S-VHS ET Recording Indicator Indications During Recording EN51 Tape Counter Tape Running Indicator Playback Indications During Playback Indications FunctionUse only the following batteries To prevent damage and prolong service life52 EN To avoid hazardEN53 To prevent damage to the LCD monitor, do not To prolong service lifeCleaning The Camcorder About moisture condensationConnectors Optional AccessoriesGeneral GR-FX36EDGR-FXM66EDGR-SX56EDGR-SXM76EDGR-SXM85EDGR-SXM86ED
Top Page Image Contents