JVC GR-SXM86ED specifications Charging the Battery Pack, Power, To Detach The Battery Pack

Page 6
Make sure the battery pack is attached to the camcorder. Hook its end to the camcorder 1 and push the battery in until it locks in place 2.
•If the battery pack is attached in the wrong position, a malfunction may occur.
Set the Power Switch to “OFF”. Connect the AC Adapter to the camcorder 3, then connect the Power Cord to the AC Adapter 4.
Plug the Power Cord into an AC outlet 5. The CHARGE lamp on the camcorder blinks to indicate charging has started.

6EN

Hook on.

Power

GETTINGSTARTED

1

2 Push in.

BATTERY RELEASE Switch

REFRESH Button

REFRESH Lamp

CHARGE Lamp

Battery pack

Power Switch

 

To AC outlet

3 To DC IN

 

connector

5

 

4

AC Adapter

 

Battery pack

Charging time

BN-V11U

approx. 1 hr. 30 min.

BN-V12U (optional)

approx. 1 hr. 30 min.

BN-V20U (optional)

approx. 2 hrs. 20 min.

BN-V400U (optional)

approx. 4 hrs. 30 min.

This camcorder’s 2-way power supply system lets you choose the most appropriate source of power. Do not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

1

2

3

4 When the CHARGE lamp stops blinking but stays lit, charging is finished. Unplug the Power Cord from the AC outlet. Disconnect the AC Adapter from the camcorder.

To Detach The Battery Pack . . .

.... slide BATTERY RELEASE and pull out the battery pack.

NOTES:

●During charging or discharging, the camcorder cannot be operated.

●Charging and discharging is not possible if the wrong type of battery is used.

●When charging the battery pack for the first time or after a long storage period, the CHARGE lamp may not light. In this case, remove the battery pack from the camcorder, then try charging again.

●If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.

●Using the optional AA-V15 AC Power Adapter/Charger, you can charge the BN-V11U/V12U/V20U/V400U battery pack without the camcorder. However, it cannot be used as an AC adapter.

REFRESH:

Charging a battery with some charge remaining reduces that battery’s capacity. Perform the procedure below to fully discharge the battery pack before recharging.

1.Perform steps 1 through 3 of “CHARGING THE BATTERY PACK”.

2.Press REFRESH on the camcorder for over 2 seconds. The REFRESH lamp on the camcorder blinks to indicate discharging has started.

3.When discharging is finished, charging automatically starts and the CHARGE lamp blinks.

When you are not using a battery pack for a long period of time, be sure to fully discharge it before storing because leaving a battery with some charge left over also reduces performance.

For other notes, ☞ pg. 44

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Instructions Dear Customer It is recommended that you EN3 Models equipped with LCD monitor onlyPower Cord Remote Control Unit RM-V716U Battery Pack Automatic DemonstrationHow To Attach The Core Filter EN5To Detach The Battery Pack Charging the Battery PackPower Slide Battery Release and pull out the battery packEN7 Using the Battery PackUsing AC Power Approximate recording time unit minGrip Adjustment Tripod MountingComes on Date/Time SettingsPower lamp Rotate Menu to selectRecording Format Setting 10 ENEN11 Regular VHS VCRRecording Mode Setting Tape Length SettingLoading/Unloading a Cassette EN13To Stop Recording 14 ENShooting While Watching Rotate Bright until the bright levelEN15 SELF-RECORDINGmodels equipped with LCD monitor onlyJournalistic Shooting models equipped with LCD monitor only 16 EN ZoomZoom Out EN17 Press the Recording Start/Stop Button to start recordingNight-Scope 18 ENSnapshot If you press during Record-StandbyFade/Wipe Effects EN19Fades in/out to a black screen 20 EN Program AE With Special EffectsDigital Effects EN21Using Menus For Detailed Adjustment If you select Jlip ID noMenu Screen Explanations Camera MenuSystem Menu 24 EN Date/Time Insert Instant TitlesTime-Lapse Set REC Time and 2 of Animation aboveSet the Power Switch to Press MENU. The Menu Screen appears Exposure ControlEN27 Auto Focus Focusing28 EN Manual FocusEN29 White Balance AdjustmentManual White Balance Operation Press Menu again to close the Menu ScreenLoad a tape pg Set the Power Switch to 30 ENTo cancel the effect, select OFF in step EN31Use the provided A/V cable and S-Video cable Use the provided A/V cableTape Dubbing Power supply instead of the battery pack pgBasic Connections EN33Cover 34 ENCassette Adapter Slide the latch to open the adapter compartmentEN35 Functions ButtonsEN Using the Remote Control Unit Press Play to find the scene of interest EN37Playback Zoom To End Zoom38 EN Insert EditingAudio Dubbing EN39For Insert Editing and Audio Dubbing Press Shift for this one 40 ENSET REMOTE/VCR Code You are now ready to try Random Assemble EditingMake Connections Connect the editing cable to the R.A.EDIT connectorEN41 Connect the editing cable to the Remote Pause terminal42 EN Select ScenesOUT 9 the scene you want to edit and press Pause Editing cable and the A/V cable44 EN SettingsCharging time varies according to the ambient temperature Date/TimeTBC TBC indicator turns green grey with a camcorder equippedRecording Time BaseRecording does not start No power is suppliedRecording cannot be performed Animation or Time-Lapse is notLens CAP warning indicator may blink when An error number i.e. E03 appearsThat Date/Time setting is carried out Lens CAP warning indicator48EN 3 4 5 y u # $ %EN49 50 EN Night-Scope Indicator ................... pgVHS/S-VHS ET Recording Indicator Indications During RecordingEN51 Tape Counter Tape Running Indicator PlaybackIndications During Playback Indications FunctionUse only the following batteries To prevent damage and prolong service life52 EN To avoid hazardEN53 To prevent damage to the LCD monitor, do not To prolong service lifeCleaning The Camcorder About moisture condensationConnectors Optional AccessoriesGeneral GR-FX36EDGR-FXM66EDGR-SX56EDGR-SXM76EDGR-SXM85EDGR-SXM86ED
Top Page Image Contents