JVC GY- HD101, GY-HD100 manual AC Operation, Charging the Built-in Battery, How to charge

Page 35

PREPARATIONS

AC Operation

		POWER lamp
		To plug outlet
DC IN		DC OUT
connector	AC adapter	connector
	Ferrite core

DC cable

The GY-HD100 is operable with AC power supply or battery pack.

Use the supplied AC adapter as the AC power supply.

1.After making sure that the power switches of the GY- HD100 and of the AC adapter are set to OFF, connect the DC cable from the AC adapter to the DC IN connector of the GY-HD100 as shown in the illustration.

2.Press the POWER switch of the GY-HD100 to ON. Power is supplied to the VTR section and the camera.

CAUTION

•When using the DC cable make sure to connect the end of the cable with the ferrite core to the AC adapter.

•Do not remove or connect the DC cable while recording is being performed.

•Do not use any power source with large fluctuations in the power source voltage, power sources generating noise, such as ripples or power sources with lower voltage.

Attach the supplied core filter (gray) as shown in the diagram on the right to reduce unwanted electromagnetic emission.

zAttach the core filter as shown in the diagram on the left to this unit as near as possible.

Core filter (gray)

Charging the Built-in Battery

The built-in, rechargeable backup battery retains the date and time and the time code data.

The built-in battery is constantly being charge whenever the GY-HD100 is connected to a power supply, but it gradually discharges while the GY-HD100 is disconnected from a power supply. The battery will be fully discharged when the GY-HD100 is not used for about three months, in which case the set date and time and time code data are reset.

In this case, recharge the built-in battery and then set the date and time and time code data again.

However, it is possible to use the GY-HD100 even if the built- in battery is discharged but the date and time and time code data cannot be recorded.

How to charge

1.Connect the provided AC adapter to the GY-HD100 and an AC outlet or mount a charged battery on the GY- HD100.

2.Set the POWER switch on the GY-HD100 to “ON” or “OFF” (charging takes places with the POWER switch set to either of the positions.)

3.Leave the equipment in this condition for about 4 hours.

•The built-in battery will remain charged for about 3 months after being charged for about 4 hours.

31

Image 35

Contents For Customer Use GY-HD101Page Important Safety Instructions Remarque For USA and CanadaPort Cable Length LensMicrophone AccessoriesMain Features Contents Contents Introduction Precautions for Proper UseRoutine and Periodical Mainte- nance Precautions for Use of Head Cleaning TapeHead Cleaning Periodical Maintenance„ For recording and storing videotapes Best condition Battery Pack to be UsedVideocassette to be Used Condensation Characteristic CCD PhenomenaTh16 x 5.5BRMU CONTROLS, Indicators and ConnectorsZoom Lens Optional Front Section Rear Section LCD Door 2CH-1/CH-2 Audio Select CH-1/CH-2 audio selector switch3TC Display TC/UB display switch 5CAM/VTR Camera/VTR mode switch buttonRight Side Section HHDV/DV LED BGAIN Sensitivity selector switchCWHT.BAL White balance switch DStandLeft Side Section Top Section KPLAY/STILL Play/still button GVTR VTR indicatorTop Section Cont’d FDISPLAY Display button„ Status Screens Indications on the LCD Monitor and in the ViewfinderIndications on the LCD Monitor and in the Viewfinder Cont’d „ Status Screens in the Camera ModeSetting Status Contents of Indications Contents See ND1 Filter ND1 1/4ND Indication Indication Contents „ Status Screen in VTR Mode „ Safety Zone Indication Camera mode only „ Auto White Balance Indication Camera mode only„ Menu Setting Screen „ Alarm Message DisplayLCD Closed Normal LCD Basic System PreparationsKnob How to Attach the ViewfinderAttaching the Zoom Lens Provided Attaching the Microphone Provided„ Taking out the SD memory card Inserting an SD Memory CardAbout the Viewfinder Cable „ Inserting an SD Memory CardAC Operation „ Charging the Built-in Battery„ How to charge „ Detaching the Battery Pack from the GY HD100 Battery Operation„ Charging the Battery Pack „ Attaching the Battery Pack on the GY HD100„ Precautions for the Battery Pack „ Remaining Battery Power Display„ Battery Recharge Times „ Operating Time with Battery PackPreparations for Operation Turning the Power on„ Turning the Power on „ Turning the Power OFFMode Loading/Unloading the Cassette„ Cassette Loading „ Unloading the Cassette„ Setting the Date and Time Style Setting and Displaying the Date and Time„ Displaying the Time and Date on the Screen „ Setting the Date and TimeDisplaying Time Code „ SettingNON Presetting and Recording of Time CodeDrop frame/Non-drop frame mode Drop„ Zero-resetting the Time Code or User’s Bit Data Presetting and Recording of Time Code Cont’d„ Presetting time cord data „ Presetting user’s bit dataViewfinder Adjustment Screen AdjustmentBack Focus Adjustment „ Error messages White Balance Adjustment„ White Balance Adjustment „ Adjustment procedure„ About the Motion Smooth Function Setting the Video Format„ Setting the Frame Rate Item „ Setting the REC ItemND Filter Camera SettingsScreen Size 43/169 Mode Selection „ Selecting the CH-2 channel input con Nector Audio Input Signal Selection„ Selecting the audio signal input „ Adjusting Audio during RecordingLOW/MIDDLE/HIGH „ Monitoring Audio during Recording„ About the Focus Assist Function Shooting OperationBasic Recording Operation Shooting Operation „ If the Record-Standby Mode ContinuesHeader REC Function Function/Initial Setting„ How to set the Header REC menu screen Search Playback ModePlayback Procedure Fast-Forward, RewindMonitor PB Audio CH DV Outputting AudioMIX Stereo„ Displaying Alarms Using External ComponentsConnecting the Video Signal Cables „ Connecting the IEEE1394 CableDubbing with AV Devices HDV/DV Dubbing OFF „ Operation Backup Recording„ Settings „ ConnectionsMenu Screens Menu Screen ConfigurationSetting Menu Screens TOP Menu Screen Video Format Menu Screen Function/Setting bold characters indicate initial settingsSetting Description Auto Connector G Unconnected Connected Output SignalInitial settings U model 7.5% E model 0.0% NativeOFF Camera Operation Menu Screen3200K Normal Camera Process 1/2 Menu ScreenMiddle High108% Camera Process 2/2 Menu ScreenStandard Advanced Process Menu ScreenStop Color Matrix Adjust Menu ScreenSkin Color Adjust Menu Screen None Switch Mode Menu ScreenREC Item Setting for Step Setting for Variable StepMIX AUDIO/MIC Menu ScreenBlue LCD/VF 1/3 Menu Screen70-80% TC/UB LCD/VF 2/3 Menu ScreenTape Remain VF Contrast LCD/VF 3/3 Menu ScreenLCD Contrast Drop TC/UB/CLOCK Menu ScreenExecute Header REC Menu Screen DisableVariation Range U model MM/DD/YY E model DD/MM/YY TIME/DATE Menu ScreenBARS+CAM DATE+TIMEBlink Others 1/2 Menu Screen3MIN Others 2/2 Menu Screen „ Displaying the File Manage menu Screen „ Loading a menu settings fileFile Manage Menu Screen File Manage Menu Screen Cont’d „ Saving settings„ Error displays „ Initializing formatting an SD memory Card „ Resetting the menu settings to the fac Tory settings„ Setting the skin detail function color and range Features of the Camera SectionHow to Use Skin Detail „ Using the Skin Detail Function Features of the Camera SectionOutputting color bars Display Status Action OthersError Code Error Details GY-HD100 Operation Remedy Viewfinder Screen Blinking Pattern Remaining Battery/TapeSymptoms Remedy TroubleshootingBusiness users Other Countries outside the European Union How to Display the Hour MeterInformation for Users on Disposal of Old Equipment European UnionSpecifications Accessories