JVC GY- HD101, GY-HD100 manual Monitoring Audio during Recording, Low/Middle/High

Page 51

SETTING AND ADJUSTMENTS BEFORE SHOOTING

PHONES jack

CAUTION

•When the AUDIO INPUT switch is set to MIC, be sure to check that the microphone is connected to the INPUT1/2 connector. If the microphone is not connected, increasing the audio level could cause noise from the input connec- tor to be recorded on the tape. When the microphone is not connected to the INPUT1/2 connector, set the AUDIO INPUT switch to “LINE” or turn down the audio level con- trol.

•In the FULL AUTO mode, the audio level volume cannot be adjusted with the audio level controls on the CH-1 and CH-2.

MEMO

The reference level for audio recorded on the tape can be set with the AUDIO REF. LEVEL item on the AUDIO/MIC menu screen. (–20 dB or –12 dB) The level will change for both CH-1 and CH-2.

Monitoring Audio during Recording

The audio input during recording, in record-pause or stop mode can be monitored through the monitoring speaker or earphone.

•Select the audio channel to be monitored using the MONI- TOR SELECT switch.

CH-1 : The sound input to the CH-1 channel is output.

BOTH : The sound input to the CH-1 and CH-2 channels is output mixed.

CH-2 : The sound input to the CH-2 channel is output.

•The MONITOR volume control adjusts the monitoring vol- ume.

•The loudspeaker or earphone outputs an alarm tone in the case of an abnormal condition occurring in the unit.

An alarm tone is also output when the tape end is reached or when the battery is running down.

*Do not increase the audio monitoring volume exces- sively; otherwise howling with the camera microphone may occur.

MEMO

•When connecting a stereotype earphone, make the fol- lowing settings to output stereo sound.

1Set the MONITOR SELECT switch to BOTH.

2Set the AUDIO MONITOR item on the AUDIO/MIC menu screen to STEREO.

•When AUDIO MONITOR item on the AUDIO/MIC menu screen is set to “STEREO”, only the audio of CH-1 is out- put from the monitoring speaker.

•The volume of the alarm tone is set with the ALARM VR LEVEL item on the OTHERS [1/2] menu screen. (OFF/

LOW/MIDDLE/HIGH)

47

Image 51

Contents For Customer Use GY-HD101Page Important Safety Instructions Remarque For USA and CanadaPort Cable Length LensMicrophone AccessoriesMain Features Contents Contents Introduction Precautions for Proper UseRoutine and Periodical Mainte- nance Precautions for Use of Head Cleaning TapeHead Cleaning Periodical MaintenanceBattery Pack to be Used Videocassette to be Used„ For recording and storing videotapes Best condition Condensation Characteristic CCD PhenomenaCONTROLS, Indicators and Connectors Zoom Lens OptionalTh16 x 5.5BRMU Front Section Rear Section LCD Door 2CH-1/CH-2 Audio Select CH-1/CH-2 audio selector switch3TC Display TC/UB display switch 5CAM/VTR Camera/VTR mode switch buttonRight Side Section HHDV/DV LED BGAIN Sensitivity selector switchCWHT.BAL White balance switch DStandLeft Side Section Top Section KPLAY/STILL Play/still button GVTR VTR indicatorTop Section Cont’d FDISPLAY Display button„ Status Screens Indications on the LCD Monitor and in the Viewfinder„ Status Screens in the Camera Mode Setting Status Contents of IndicationsIndications on the LCD Monitor and in the Viewfinder Cont’d Contents See ND1 Filter ND1 1/4ND Indication Indication Contents „ Status Screen in VTR Mode „ Safety Zone Indication Camera mode only „ Auto White Balance Indication Camera mode only„ Menu Setting Screen „ Alarm Message DisplayLCD Closed Normal LCD Basic System PreparationsKnob How to Attach the ViewfinderAttaching the Zoom Lens Provided Attaching the Microphone Provided„ Taking out the SD memory card Inserting an SD Memory CardAbout the Viewfinder Cable „ Inserting an SD Memory Card„ Charging the Built-in Battery „ How to chargeAC Operation „ Detaching the Battery Pack from the GY HD100 Battery Operation„ Charging the Battery Pack „ Attaching the Battery Pack on the GY HD100„ Precautions for the Battery Pack „ Remaining Battery Power Display„ Battery Recharge Times „ Operating Time with Battery PackPreparations for Operation Turning the Power on„ Turning the Power on „ Turning the Power OFFMode Loading/Unloading the Cassette„ Cassette Loading „ Unloading the Cassette„ Setting the Date and Time Style Setting and Displaying the Date and Time„ Displaying the Time and Date on the Screen „ Setting the Date and TimeDisplaying Time Code „ SettingNON Presetting and Recording of Time CodeDrop frame/Non-drop frame mode Drop„ Zero-resetting the Time Code or User’s Bit Data Presetting and Recording of Time Code Cont’d„ Presetting time cord data „ Presetting user’s bit dataViewfinder Adjustment Screen AdjustmentBack Focus Adjustment „ Error messages White Balance Adjustment„ White Balance Adjustment „ Adjustment procedure „ About the Motion Smooth Function Setting the Video Format „ Setting the Frame Rate Item „ Setting the REC ItemCamera Settings Screen Size 43/169 Mode SelectionND Filter „ Selecting the CH-2 channel input con Nector Audio Input Signal Selection„ Selecting the audio signal input „ Adjusting Audio during RecordingLOW/MIDDLE/HIGH „ Monitoring Audio during RecordingShooting Operation Basic Recording Operation„ About the Focus Assist Function Shooting Operation „ If the Record-Standby Mode ContinuesHeader REC Function Function/Initial Setting„ How to set the Header REC menu screen Search Playback ModePlayback Procedure Fast-Forward, RewindMonitor PB Audio CH DV Outputting AudioMIX Stereo„ Displaying Alarms Using External ComponentsConnecting the Video Signal Cables „ Connecting the IEEE1394 CableDubbing with AV Devices HDV/DV Dubbing OFF „ Operation Backup Recording„ Settings „ ConnectionsMenu Screens Menu Screen ConfigurationSetting Menu Screens TOP Menu Screen Function/Setting bold characters indicate initial settings Setting DescriptionVideo Format Menu Screen Auto Connector G Unconnected Connected Output SignalInitial settings U model 7.5% E model 0.0% NativeCamera Operation Menu Screen 3200KOFF Normal Camera Process 1/2 Menu ScreenMiddle High108% Camera Process 2/2 Menu ScreenStandard Advanced Process Menu ScreenColor Matrix Adjust Menu Screen Skin Color Adjust Menu ScreenStop None Switch Mode Menu ScreenREC Item Setting for Step Setting for Variable StepMIX AUDIO/MIC Menu ScreenLCD/VF 1/3 Menu Screen 70-80%Blue LCD/VF 2/3 Menu Screen Tape RemainTC/UB LCD/VF 3/3 Menu Screen LCD ContrastVF Contrast TC/UB/CLOCK Menu Screen ExecuteDrop Header REC Menu Screen DisableVariation Range U model MM/DD/YY E model DD/MM/YY TIME/DATE Menu ScreenBARS+CAM DATE+TIMEOthers 1/2 Menu Screen 3MINBlink Others 2/2 Menu Screen „ Loading a menu settings file File Manage Menu Screen„ Displaying the File Manage menu Screen „ Saving settings „ Error displaysFile Manage Menu Screen Cont’d „ Initializing formatting an SD memory Card „ Resetting the menu settings to the fac Tory settingsFeatures of the Camera Section How to Use Skin Detail„ Setting the skin detail function color and range „ Using the Skin Detail Function Features of the Camera SectionOutputting color bars Display Status Action OthersError Code Error Details GY-HD100 Operation Remedy Viewfinder Screen Blinking Pattern Remaining Battery/TapeSymptoms Remedy TroubleshootingBusiness users Other Countries outside the European Union How to Display the Hour MeterInformation for Users on Disposal of Old Equipment European UnionSpecifications Accessories