JVC GY-HD200U/CHU Presetting and Recording of Time Code, Time code generator’s running method is

Page 82

PREPARATIONS FOR OPERATION

Presetting and Recording of Time Code

The time codes from the internal time code generator can be recorded at the time of recording scenes.

•The TC/UB/CLOCK menu screen differs depending on whether the FRAME RATE item on the VIDEO FORMAT

menu screen is “60/30” or “50/25”.

There are two ways to preset the time code.

•Set from the TC/UB/CLOCK menu screen.

•Set in the LCD screen without opening the menu screen. This section explains how to set from the TC/UB/CLOCK menu screen.

* See page 46 for instructions of setting from the LCD screen.

Menu and switch settings to set the time code preset are the same as the settings below.

Setting

To preset the Time Code, make the following settings.

„TC GENE. switch Set to REC or FREE.

REC

: The data preset in the time code generator

 

runs only during recording.

 

Use this setting if it is necessary to record

 

continual time codes across different scenes.

 

* However, approximately ±1-frame varia-

 

tions may occur in scene accuracy.

FREE

: The time code starts to run from the time it is

 

preset in the time code generator.

„Set the TCG SOURCE item in the TC/UB/CLOCK menu screen to INTERNAL.

„TC/UB/CLOCK menu screen (FRAME RATE: 60/30)

Use the DROP FRAME item to select the framing mode for the time code generator.

DROP

: The time code generator’s running method is

 

set the drop frame mode.

 

Use this setting when placing emphasis on

 

the recording time.

NON

: The time code generator’s running method is

DROP

set to the non drop frame mode.

 

Use this setting when placing emphasis on

 

the number of frames.

TC/UB/CLOCK menu screen

(FRAME RATE: 60/30)

Framing mode:

Drop frame/

Non-drop setting

MEMO

Drop frame/Non-drop frame mode

In the NTSC system, the actual number of frames per 1 second is approximately 29.97 frames, but per time code 30 frames are processed. To compensate for this differ- ence, the mode called “drop mode” drops frame 00 and 01 for every minute not divisible by 10.

The “non-drop frame mode” is when no frames are dropped and the actual time shift neglected.

„TC/UB/CLOCK menu screen (FRAME RATE: 50/25) Whether or not user’s bit data should be recorded can be selected with the UB REC item on the TC/UB/CLOCK menu screen.

Presetting time code data

The time code and user’s bit data are preset on the TC/UB/ CLOCK menu screen.

1.Display the TC/UB/CLOCK menu screen.

Select the TC/UB/CLOCK item on the TOP MENU screen.

Time code (hour, min, sec, frame)

2.Set the time code (hours, minutes, seconds, frames).

1Rotate the SHUTTER dial to align the cursor (K) with TC PRESET, and then press the SHUTTER dial.

•The first digit of the time code blinks. The blinking digit is the one to be set.

2When the SHUTTER dial is pressed, the blinking digit changes.

3When the SHUTTER dial is rotated, the value of the blinking digit changes.

When the SHUTTER dial is rotated upward, the value becomes higher. When rotated downward, the value becomes smaller.

4Repeat the procedure described in 2 and 3 above to set the desired value for all digits.

5After setting the frame digit, press the SHUTTER dial to make EXECUTE blink. The setting values are con- firmed when the SHUTTER dial is pressed again.

To cancel the setting, select CANCEL and press the

Presetting user’s bit data

The user’s bit data are preset with the UB PRESET item on the TC/UB/CLOCK menu screen.

The method for setting is the same as the method for setting the time code described on the left.

•The user’s bit can be specified using numerals or alpha- betic letters from 0 to F for each digit.

•To record user’s bit data, set the UB REC item to ON (Only when set to FRAME RATE 50/25).

CAUTION

It is not possible to set all the digits of the user’s bit data to “F”.

Reading of the data during playback will not be possible for an all-F setting.

Zero-resetting the Time Code or User’s Bit Data

This is performed with the TC or UB PRESET item on the TC/UB/CLOCK menu screen. (Performed separately for the time code and the user’s bit data.)

1Rotate the SHUTTER dial to align the cursor (K) with the TC or UB PRESET item, and then press the SHUTTER dial.

2Rotate the SHUTTER dial to select ZERO PRESET as the setting value, and then press the SHUTTER dial.

MEMO

When a menu screen is not being displayed, you can zero reset the time code data by simultaneously holding down the USER2 button and the STOP button for about 1 sec- ond.

TC/UB/CLOCK menu screen

(FRAME RATE: 50/25)

SHUTTER dial.

3.When all the digits are set

•Press the STATUS button to return to the normal screen

or

•Rotate the SHUTTER dial to align the cursor (K) with the PAGE BACK item, and then press the SHUTTER dial to return to the TOP MENU screen.

44

45

Page 81 Page 83
Image 82
Page 81 Page 83
Contents GY-HD200U/CHU Instructions GY-HD200E/CHE GY-HD201E/CHE For Customer UseSafety Precautions Important SafeguardsRemarque Information for Users on Disposal of Old Equipment Safety Precautions Cont’dThis symbol is only valid in the European Union European UnionSee pages 12, 36 For DC ×2/EarphoneSee SD memory card SeeContents Precautions for Use of Head Cleaning Tape Precautions for Proper UseRoutine and Periodical Maintenance Head CleaningCondensation Battery Pack to be UsedCharacteristic CCD Phe- nomena Videocassette to be UsedTh16 × 5.5BRMU Zoom LensFront Section MemoRear Section LCD DoorRight Side Section Left Side Section Top Section Recording and Image Out- put Formats Indications on the LCD Monitor and in the View- finder Status Screens in the Camera ModeSetting Status Contents of Indications Status ScreensContents Indications on the LCD Monitor and in the Viewfinder Cont’dIndication Indication Contents Magnified Status Indications on LCD Monitor NDFMenu Setting Screen Alarm Message DisplaySwitching between the LCD Screen and Viewfinder Display Safety Zone Indication Camera mode onlyBasic System Attaching the Zoom Lens How to Attach the View- finderAttaching the Microphone Provided Attaching the Tripod Base Optional Inserting an SD Memory CardBattery Operation AC OperationTurning the Power on Loading/Unloading the Cassette Setting and DisplayingDate and Time Displaying Time Code SettingDisplaying the Time and Date on the Screen Presetting time code data Presetting and Recording of Time CodeSetting Presetting user’s bit dataAbout Time Code Mode Presetting User’s BitAborting Preset Operation Playing Back Time CodeScreen Adjustment Viewfinder AdjustmentWhite Balance Adjustment Back Focus AdjustmentWhite Balance Adjustment Full Auto White Balance FAWSetting the Frame Rate Item White Shading AdjustmentSetting the Video Format Setting the REC ItemAudio Input Signal Selec- tion Camera SettingsScreen Size 43/169 Mode Selection Monitoring Audio during Recording Audio Input Signal Selection Cont’dBasic Recording Opera- tion About the Focus Assist FunctionFunction/Initial Setting If the Record-Standby Mode Contin- uesRecord-Standby or Stop mode Header REC FunctionHeader REC Function Playback ProcedureSearch Executing the Header REC FunctionConnecting the IEEE1394 Cable Connecting the VideoSignal Cables Displaying AlarmsDubbing with AV Devices HDV/DV DubbingHDV/DV Dubbing Cont’d Backup RecordingSettings OFFConnect a Remote Con- trol Unit RM-LP55/RM- LP57 Remote Control Unit Functions ListShutter Speed in 24p Mode ConnectionMenu Screen Configura- tion Setting Menu Screens TOP Menu ScreenVideo FORMAT1/2 Menu Screen Function/Setting bold characters indicate initial settingsSetting Description Frame RateMenu Screen Initial settings U model 7.5% E model 0.0%Video FORMAT2/2 Menu Screen AutoNormal MiddleHigh 108%Standard StopREC Item Setting for Step Setting for Variable Switch Mode Menu ScreenSwitch Mode menu screen is only displayed in camera mode White Balance Menu ScreenAUDIO/MIC2/2 Menu Screen AUDIO/MIC1/2 Menu ScreenMIX LCD/VF2/4 Menu Screen LCD/VF2/4 menu screen can only be set in camera modeLCD/VF1/4 Menu Screen 70-80%LCD/VF3/4 Menu Screen Screen is displayed in the VTR modeLCD/VF4/4 Menu Screen Header REC Menu Screen DisableTC/UB/CLOCK Menu Screen DropTIME/DATE Menu Screen OTHERS1/2 Menu ScreenOTHERS2/2 Menu Screen 1394Error displays Loading a menu settings fileSaving settings File Manage Menu ScreenInitializing formatting an SD mem- ory card How to Use Skin DetailRotate Using the Skin Detail Function How to Use Skin Detail Cont’dOutputting Color Bars Display Status Action Error Code Error Details This device Operation Remedy Blinking Pattern Remaining Battery/TapeHow to Display the Hour Meter TroubleshootingSymptoms Remedy External Dimensions unit mm SpecificationsHDV GY-HD251 Safety Precautions Important SafeguardsRemarque Port Cable Length HD251CHE See Provided only for U modelContents Routine and Periodical Maintenance Precautions for Proper UsePrecautions for Use of Head Cleaning Tape Condensation Battery Pack to be UsedCharacteristic CCD Phe- nomena Videocassette to be UsedIris A/R Input Zoom LensFront Section GNDAccording to the input level. When excessive 4TC GENE. Time code generator setting switchSetting, the time code always operates Rear SectionRight Side Section BGAIN Sensitivity selector switchPreset EREC REC trigger button start/stop recordingLeft Side Section RCATop Section Ieee Recording and Image Out- put FormatsRecording Composite Indications on the LCD Monitor and in the View- finder Indications on the LCD Monitor Viewfinder Cont’dFile Filter OFF ND1ND2 Full Auto ON, OFF GainEXT NDFCenter Mark OFF Safety ZoneSafety Zone OFF DV-24PAFinder How to Attach the ViewBasic System Attaching the Zoom Lens Attaching the Microphone ProvidedInserting an SD Memory Card SDHC-compliant memory cards cannot be used with this device„GY-HD250U Battery OperationAC Operation „GY-HD251ETurning the Power on Date and Time Setting and DisplayingLoading/Unloading the Cassette VTRDisplayed Time Code/User’s Bit Time code input entered the IEEE1394 connectorDisplaying Time Code Time codes are displayedTime code starts to run from the time it is Presetting and Recording of Time CodeContinual time codes across different scenes Time code generator’s running method isInternal Presetting the Time Code from the LCD ScreenPlaying Back Time Code Free REC Regen InternalExternal Blinks when the time code cannot be synchronizedSlave unit GY-HD250U/GY-HD251E/GY-HD110U/GY- HD111E TC OUTBack Focus Adjustment Screen Adjustment Viewfinder AdjustmentAdjusted Adjust the position and angle of the viewfinder Set the ND filter switch according to the current lighting White Balance AdjustmentWhite Shading Adjustment When correct white balance is obtained, the approximateScreen Size 43/169 Mode Selection Setting the Video FormatCamera Settings ND FilterAudio Input Signal Selec- tion Basic Recording Opera- tion How to set the Header REC menu screen Header REC FunctionFast-Forward, Rewind Playback ProcedureOutputting Audio SearchRecording Composite Video Signals from an External Device Connecting the VideoSignal Cables Status Screen Display on the LCD Screen or ViewfinderAdjust SC and H Phase Using Genlock Func- tionsSynchronized Signals Dubbing with AV DevicesHDV/DV Dubbing Backup Recording Connect a Remote Con- trol Unit RM-LP55/RM- LP57Menu Screen Configura- tion Connect a Remote Control Unit RM-LP55/RM-LP57 Cont’dSetting Menu Screens Menu Screen Configuration Cont’dOFF TOP Menu ScreenVideo FORMAT1/2 Menu Screen ExecuteVideo FORMAT2/2 Menu Screen Video FORMAT1/2 Menu Screen Cont’dMiddle Menu Screen3200K High108% NormalStandard White Balance Menu Screen PresetStop Step Switch Mode Menu ScreenAUDIO/MIC1/2 Menu Screen NoneMIX AUDIO/MIC2/2 Menu ScreenLCD/VF1/4 Menu Screen BlueVoltage LCD/VF2/4 Menu ScreenLCD/VF3/4 Menu Screen SECColor LCD/VF4/4 Menu ScreenTC/UB/CLOCK Menu Screen InternalHeader REC Menu Screen TIME/DATE Menu Screen3MIN OTHERS1/2 Menu ScreenOTHERS2/2 Menu Screen BlinkGenlock Menu Screen OTHERS2/2 Menu Screen Cont’d100 101 File Manage Menu ScreenIf you want to change the range of colors recognized with How to Use Skin DetailSkin color detection function, follow the steps below 104 105 Outputting Color BarsSwitch No DV SignalNo HDV Signal Switch to VTRError Code Error Details GY-HD250/GY-HD251 Remedy Operation How to Display the Hour Meter TroubleshootingRGB? Genlock input SpecificationsAUX input HD/SD SDI outputCorrection
Top Page Image Contents