JVC LYT1145-001A manual Charging the Battery Pack, Using the Battery Pack, Using AC Power

Page 7

Power

CHARGING THE BATTERY PACK

1 With the arrow on the battery pack pointing upward, push the battery pack slightly against the battery pack mount #, then slide up the battery pack until it locks in place.

2 Set the Power Switch u to “OFF (CHARGE)”. Connect the AC Adapter to the camcorder, then connect the Power Cord to the AC Adapter.

3 Plug the Power Cord into an AC outlet. The POWER/CHARGE lamp t on the camcorder blinks to indicate charging has started.

4 When the POWER/CHARGE lamp t goes off, charging is finished. Unplug the Power Cord from the AC outlet. Disconnect the AC Adapter from the camcorder.

To Detach The Battery Pack:

Slide the battery pack down slightly while sliding down BATT. RELEASE W to detach it.

Battery pack

Charging time

 

 

BN-V408U

approx. 1 hr. 30 min.

 

 

BN-V416U (optional)

approx. 3 hrs.

 

 

BN-V428U (optional)

approx. 5 hrs.

 

 

Charging times are for a fully discharged battery pack.

USING THE BATTERY PACK

Perform step 1 of “CHARGING THE BATTERY PACK”.

Approximate recording time

Battery pack

LCD monitor on

Viewfinder on

 

 

 

BN-V408U

1 hr. 10 min.

1 hr. 40 min.

 

 

 

BN-V416U

2 hrs. 30 min.

3 hrs. 30 min.

(optional)

 

 

 

 

 

BN-V428U

4 hrs. 20 min.

6 hrs. 20 min.

(optional)

 

 

 

 

 

BN-V840U

5 hrs. 20 min.

7 hrs. 30 min.

(optional)

 

 

 

 

 

BN-V856U

8 hrs. 10 min.

11 hrs. 10 min.

(optional)

 

 

 

 

 

USING AC POWER

Connect the AC Adapter to the camcorder as shown in the following illustration.

•The provided AC Adapter features automatic voltage selection in the AC range from 110 V to 240 V.

#t u

Arrow

Battery pack

To DC

W

connector

 

AC Adapter

 

 

To AC outlet

ATTENTION

Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can result in a camcorder malfunction.

INFORMATION

The extended-use battery pack kit is a set composed of a battery pack and AC Power Adapter/Charger:

VU-V840 KIT : BN-V840U battery pack & AA-V15EK AC Power Adapter/Charger

VU-V856 KIT : BN-V856U battery pack & AA-V80EK AC Power Adapter/Charger

Read the kit's instruction manual before using. Also, by using the optional JVC VC-VBN856U DC Cord, it will be possible to connect BN-V840U or BN-V856U battery packs to the camcorder and supply power directly to the camcorder.

NOTES:

●If the protective cap is attached to the battery pack, remove it first.

●During charging, the camcorder cannot be operated.

●Charging is not possible if the wrong type of battery is used.

●When charging the battery pack for the first time or after a long storage period, the POWER/CHARGE lamp t may not light. Remove the battery pack from the camcorder, then try charging again.

●If a fully-charged battery’s operation time remains extremely short, the battery is worn out. Please purchase a new one.

●Recording time is reduced significantly when Zoom or Record-Standby mode is engaged repeatedly or the LCD monitor is used repeatedly.

●Before extended use, it is recommended that you prepare enough battery packs to cover 3 times the planned shooting time.

Continued on next page.

EN

GETTING STARTED 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents GR-D70 GR-D60 Contents Blue to N Neutral or Black Brown to L Live or Red Dear Customer Before recording an important scene Some DO’S and DON’TS on the Safe USE of EquipmentSlot Make sure the arrow is Pointing upwardAC Adapter AP-V11E or AP-V13E Lens Cap See below for attachmentWind once StopperSub Menu Using AC Power PowerCharging the Battery Pack Using the Battery PackAbout Batteries Grip AdjustmentViewfinder Adjustment Lithium-ion is vulnerable in colder temperaturesLoading/Unloading a Cassette Approximate recording time Tape Recording modeShoulder Strap Attachment Tripod MountingRecording Mode Setting Date/Time SettingsScreen closes Display Loading a Memory Card Picture Quality/Image Size SettingTo Unload a Memory Card Label Clipped edge Memory cardLCD monitor fully To Adjust The Brightness Of The DisplayShooting while using the LCD monitor Open Basic RecordingSelf-Recording Operation ModePower-Linked Operation Journalistic ShootingNormal Playback To Control The Speaker VolumeTime Code Recording from the Middle of a TapePress To cancel Blank Search midwayBlank Search Press Blank SearchConnections If using a VCR . . . go to step If not . . . go to stepTo AV Connector cover Cvbs video out select switch To TV or VCRTo Protect Valuable Files available only for SD Memory Card Basic Shooting SnapshotTo Delete Unwanted Still Images To Remove The Shutter SoundMemory Card Recording Memory Card Playback Approximate Number of Storable ImagesMultiMediaCard To Magnify The Stored ImagesRemoving On-Screen Display Viewing File InformationAuto Playback Index PlaybackProtecting Files Deleting Files Advanced FeaturesTo Remove Protection To Print ALL Still Images ONE Print for Each Setting Print Information Dpof SettingTo Reset The Setting Dubbing Still Images Recorded On a Tape To a Memory CardFolder and File names To Reset The No. Of PrintsInitialising a Memory Card Making a New FolderProgramme AE With Special Effects Night-ScopeFade/Wipe Effects Auto Focus Snapshot Mode SelectionSnapshot For Tape Recording Snapshot RecordingTo Brighten The Subject Quickly Manual FocusExposure Control To Return To Automatic Exposure ControlIris Lock White Balance AdjustmentManual White Balance Operation Balance WIPE/FADERProgram AE ExposureManual Camera Display SystemFor Playback Menu DSCVideo Bright , DATE/TIME , Time Code Video DisplayPlayback Sound DisplayDubbing Dubbing To Or From a VCRTo Use This Camcorder As a Player To Use This Camcorder As a Recorder GR-D70 onlyDV cable Optional Core filter To DV Video unit equipped with DV connectorTo Use This Camcorder As a Recorder GR-D70 only To DV @ Core filterPlayback Special Effects Using the Remote Control UnitSlow-Motion Playback Frame-By-Frame PlaybackTo hear the dubbed sound during playback Set 12BIT Mode to Sound 2 or MIX Menu Screen  pgAudio Dubbing Insert EditingSET REMOTE/VCR Code Random Assemble Editing R.A.EditMake Connections Select Scenes Diagnosing VCR/CAMCORDER Timing Adjustment of VCR/CAMCORDER TimingAutomatic Editing to VCR For More Accurate EditingConnection To a Personal Computer Using USB cableUsing DV cable Using USB cableImage taken using Snapshot is too dark No power is suppliedFocus does not adjust automatically Snapshot mode cannot be usedDate/time does not appear Black & White Fader does not workImage looks like the shutter speed is too Slow White Balance cannot be activatedMemory card cannot be played back Charger indicator on the camcorder does Not lightAn error indication E01, E02 or E06 appears An error indication E03 or E04 appearsCassettes Battery PacksMemory Cards LCD Monitor How to handle a CD-ROMMain Unit About moisture condensation For Your MaintenanceCleaning The Camcorder After UseAC Adapter CamcorderLCD monitor Stereo Microphone Speaker Controls, Connectors And IndicatorsRemote Control IndexAudio/Video Input GR-D70 only Power Switch  pg pg @ Digital Video Input GR-D70 only1024 During Both Tape And Memory Card Recording LCD Monitor/Viewfinder Indications2b i t / SOUND1 During Memory Card Recording OnlyAppears when Digital Image Stabiliser DIS is Appears when in the Squeeze or Cinema modeAppears when the Insert Editing w or Insert Editing Displays the sound mode for approx seconds afterCassette Appears when no tape is loadedAppears when the tape ends during recording or playback HighE03 or E04 Unit in Safeguard Mode Eject E01, E02 or E06 Unit in Safeguard ModeAppears if a file in another format is selected RM-V717U optional Using The Optional RM-V717U Remote Control UnitTerms See previous page as well
Top Page Image Contents