Panasonic AW-HE870N Precautions for installation, Concerning electromagnetic interference

Page 12

Precautions for installation

The connection and installation should be done by qualified service personnel or system installers. Refer any servicing to qualified service personnel.

Concerning the installation location of the camera

Ensure that the installation location is strong enough to bear at least five times the total weight of the camera, lens, and cables (approx. 55.1 lbs. [25 kg]).

When mounting to a pan-tilt head or to a mounting bracket for installation, ensure that the location is strong enough to accommodate its weight as well.

The camera cannot be installed or used in the following locations.

Outdoor locations and locations where the camera may be exposed to dripping, splashing or sprayed water

Locations such as swimming pools where chemicals are used

Locations such as a kitchen where the high levels of steam and oily vapors are present and locations with flammable atmospheres or other unusual conditions

Locations where radioactive rays, X-rays or strong radio waves or magnetic fields are generated

Locations where the temperature may be outside the camera’s operating ambient temperature (14 °F to 113 °F [–10 °C to 45 °C]) range

Locations near the air outlet of an air conditioner or near a door where the camera will be exposed to incoming outside air or other locations where the temperature is subject to sudden change (since these locations may cause the lens area to cloud over and/or condensation to form)

Locations that are subject to significant vibration, such as on top of a car

Locations with high levels of humidity or dust

When the camera is not going to be used, do not leave it in place but be absolutely sure to remove it from its mounting, and put it away.

Do not run the camera cable near the wiring of electric lights.

This may result in noise interference.

Concerning electromagnetic interference

The camera’s images may become distorted or noise interference may result if the camera is used near a TV or radio transmission antenna or in strong electrical or magnetic fields (such as one generated by motors, transformers, etc.).

- 12 -

Image 12

Contents Installation instructions provided Operating InstructionsFCC Note Risk of Electric Shock Do not OpenPage Important Safety Instructions Contents Menu item setting/changing Menu item setting/changing User ModeChanging the settings Standard accessories PrefaceOperating Instructions DC cable 9.84 ft m Mounting spacerFeatures  Down converter a standard featureSpecial notes on operation Precautions for use DON’TSDOS Precautions for installation Concerning the installation location of the cameraConcerning electromagnetic interference Concerning the mounting screws and drop-prevention wire Tightening the mounting screws and mounting spacerParts to be provided by the customer for installation  Mounting screws M4 For attaching the drop-prevention wire Drop-prevention wire Major operating controls and their functions Front view / Top view / Rear view / Bottom viewFront view Top view Rear view Bottom view  Menu switch Menu  ENTER/AWB switch ENTER/AWB Lens mount  Lens fixing ring knob UP/ABB switch UP/ABB  Video output connector Video OUT Iris connector Iris  DOWN/BAR switch DOWN/BAR DC 12 V input connector 12 V  G/L input connector G/L Cable clamp  Optional card slot Option CardWhen the pan-tilt head has been used MountingLens mounting Depth 3/8˝ 10 mm  Example where the camera is mounted on a ceiling or wall CeilingWall  Example of mounting on a surface above Camera Camera mounting bracket Mounting spacer suppliedIndoor Pan/tilt Head AW-PH400 System configuration Connections Video OUTWhen an SDI card AW-HHD870 has been installed Connection of a remote operation panelInput Output Connection of the Indoor Pan-tilt Head AW-PH360  AW-IF400 Switch settings when the AW-RP400 is used HD/SD-SDI Connection of the Indoor Pan-tilt Head AW-PH400 SW1 SW2 SET UP 10BASE-T Connection of the Indoor Pan-tilt Head AW-PH405  AW-IF400 Switch settings when the AW-RP400 is used HD/SD HD/SD-SDI Connection of the Outdoor Pan-tilt Head AW-PH650  AW-IF400 Switch settings when the AW-RP400 is used HD/SD How to operate the system Control exercised from the Remote Operation Panel AW-CB400How to operate the system Procedure for camera menu operation AW-CB400 Jog dial main How to operate the system Procedure for camera menu operation AW-RP655 How to operate the system Mode How to operate the system Procedure for camera menu operation AW-RP555 Use mode setting Use Mode SettingSelecting Operating procedure Adjust the black balanceTake the shots Adjustment Flange back adjustment For zoom lensAutomatic iris power zoom lens Iris gain control in a lensWhite balance adjustment  Automatic white balance control AWB AWB A/AWB B Automatic tracking white balance setting ATW  Manual white balance setting Preset of 3200K or 5600K white balance Black balance adjustment Total pedestal level adjustment Genlock adjustment  Horizontal phase controlWhen adjusting the phase of HD signals When adjusting the phase of SD signals Adjustment by camera menu Color phase adjustment Menu item setting/changing Menu item setting Setting when using the camera by itself Main menu of Halogen, Fluorescent, Outdoor Mode Main menu of User Mode Main menu screen Sub menu Halogen, Fluorescent, Outdoor Mode Description of the setting screen  Detecting ratio adjustment Light PEAK/AVG P50 to A50 Gain setting Gain Auto, -6 dB to 18 dB  AGC maximum gain setting AGC Max Gain 6 dB, 12 dB, 18 dB Black level setting Pedestal -150 to +150 DB to -1 dB Color Set  Chroma level adjustment Chroma Level -3 to +3  Skin color adjustment Flesh Tone -3 to +3 Clean DNR setting Clean DNR Off, Low, High  Detail level setting Level Off, Low, High Subcarrier phase fine adjustment SC Fine -127 to +127  Video output format setting Format 480i, 720pHorizontal phase can be adjusted when a genlock signal  SD 480i 2D LPF SD 2D LPF Off, Low, High Component output setting Component RGB, Y/Pb/Pr, Y/C Iris Control NGPage Menu item setting/changing User Mode Sub menu User Mode Brightness Set Display  HD Detail Set Display SD Detail Set Display  Color Matrix Set Display Color Correction Set Display  G/L Set Display  Other Set Display Detecting ratio adjustment Light PEAK/AVG P50 to A50  Gain setting Gain Auto, -6 dB to 18 dB  AGC maximum gain setting AGC Max Gain 6 dB, 12 dB, 18 dB Black level setting Pedestal -150 to +150  Color Set  Chroma level adjustment Chroma Level -3 to +3 Pedestal, B Pedestal Detail band setting Detail Band 1 to  Noise suppress level setting Noise Suppress 1 to Level dependent level setting Level Dependent 0 % to 25 %  Dark detail level setting Dark Detail 0 to  Chroma detail level setting Chroma Detail 0 to Clean DNR setting Clean DNR Off, Low, High  Detail band setting Detail Band 1 to  Noise suppress level setting Noise Suppress 1 to Level dependent level setting Level Dependent 0 % to 25 %  Dark detail level setting Dark Detail 0 to  Chroma detail level setting Chroma Detail 0 to Clean DNR setting Clean DNR Off, Low, High Linear Matrix R-B MatrixR-B -31 to +31 Linear Matrix G-R MatrixG-R -31 to +31Linear Matrix G-B MatrixG-B -31 to +31 Linear Matrix B-R MatrixB-R -31 to +31Color Correction Set  G/L Set  Horizontal phase adjustment H Phase -206 to +49  Subcarrier phase fine adjustment SC Fine -127 to +127 Other Set  Gamma level setting Gamma 0.35 to  Knee level setting Knee Point 88 % to 98 %, Dynamic Flare correction level setting Flare R/G/B 0 to  Black stretch setting Black Stretch Off, On EBU matrix setting EBU Matrix Set Off, On  Video output format setting Format 480i, 720p Component output setting Component RGB, Y/Pb/Pr, Y/C Menu item setting/changing User Mode Changing the settings Changing the format settingsChanging the component setting Setting the EBU matrix Setting to initial set Factory presets Setting to initial setInitial settings of the setting items Factory preset values  Halogen, Fluorescent, Outdoor ModeUser EBU Matrix Set Troubleshooting No powerUsing the controller Cannot operateLens Cannot displayMenus  Check that the unit and lens have been connected properlySettings Camera’s imagesAre not displayed or They are disturbedSomething is wrong With the coloringPictures Pictures are tooIndicators flash Fan Error isMultiple color bands Color bars are Displayed Controller’sAppearance Unit inch mmSpecifications Video output format setting Input/Output connectorsIndicator White balanceAllowable temperature ranges Dimensions W  H  DWeight Ambient operating humidityMemo Memo Eastern Zone