Panasonic AJ- E operating instructions Audio function section output system

Page 11

Chapter 2 Parts and their functions

2-2 Audio function section (output system)

9AUDIO OUT connector (XLR, 5-pin)

The audio signals recorded on audio channels 1 and 2 or audio channels 3 and 4 are output from this connector. With the AJ-SDC905 SDC905 , the signals to be output can be selected using the MONITOR SELECT CH1/2OCH3/4 selector switch.

:MONITOR SELECT (audio channel) CH1/2OCH3/4 selector switch SDC905

This is used to select the audio channels whose signals are to be output to the speaker, earphone and AUDIO OUT connector.

CH1/2 : The signals of audio channels 1 and 2 are output.

CH3/4 : The signals of audio channels 3 and 4 are output. In addition, the channel indications for the audio level meters appearing in the display window and viewfinder change when this switch is operated.

;MONITOR SELECT (audio selection) CH1/3OSTOCH2/4 selector switch

This is used to select the audio channels whose signals are to be output to the speaker, earphone and AUDIO OUT connector in tandem with what is selected using the MONITOR SELECT switch.

CH1/3 : The signals of audio channel 1 or 3 are output.

ST : The stereo audio signals of either audio channels 1 and 2 or audio channels 3 and 4 are output. Using a menu setting, the stereo signals can be changed to MIX signals.

CH2/4 : The signals of audio channel 2 or 4 are output.

<Note>

The CH3 and CH4 audio channels are not provided with the AJ-SDC615 SDC615 . The signals of CH1 and CH2

are the ones which are selected.

MONITOR

MONITOR SELECT switch

 

 

switch

CH1/2

CH3/4

 

 

 

 

CH1/3

Audio channel 1

Audio channel 3

 

 

 

ST

Stereo2 signals of audio

Stereo2 signals of audio

channels 1 and 2

channels 3 and 4

 

 

 

 

CH2/4

Audio channel 2

Audio channel 4

 

 

 

2Either STEREO or MIX can be selected as the setting for the MONITOR SELECT item by opening the <MIC/AUDIO2> screen from the VTR MENU page by performing a menu operation.

<MONITOR (volume) control

This is used to adjust the volume of the monitor speaker or earphone.

=ALARM (warning alarm volume adjustment)

This is used to adjust the volume of the warning alarms from the earphones which have been connected to the speaker > or PHONES jack ?.

The warning alarms are not audible when this control is at its lowest setting.

> Speaker

2

The EE sound during recording or the playback sound

during playback can be monitored through this speaker. The warning alarms are output in synchronization with the flashing or lighting of the warning lamps and warning displays.

The sound heard from the speaker is automatically cut off when earphones are connected to the PHONES jack ?.

?PHONES (earphones) jack (mini jack)

This is the earphone (stereo) jack which is used to monitor the audio signals. When earphones are connected, the sound from the speaker is automatically cut off. The sound which is output from the two jacks (front and rear) is the same.

@DC OUT (DC power supply) output socket

This normally serves as the DC 12 V output socket. A current of approximately 1 A can be supplied.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model No Operating Instructions$ do not Remove Panel Cover by Unscrewing Lithium BatteryTo remove the battery/Verwijderen van de batterij Contents Menu description tables Chapter Maintenance InspectionsSpecifications 106 Features of the camera unit Features of the VTR unit ≥ Metadata supported System configuration≥ Dvcpro Ieee 1394 digital input/output connector provided ≥ Built-in time code generator/readerPower supply and accessory mounting section Rear Audio function section input systemFront Audio function section output system Shooting and recording camera unit Bars Shooting and recording VTR unitCAM. Auto Knee on CAM. Auto Knee OFF@ ECU Remote remote control connector = Output SEL output signal selection switchVideo OUT Character switch ? Video OUT video signal output connectorMenu operation section CTL Time code related sectionNDF Slave Hold W Remaining tape and remaining battery chargeDisplay window and its displays Displays relating to the VTR unit’s operations and modesDisplays relating to the time code Time code-related switch settings and display itemsMode displays TCG switch position Display switch Display item PositionViewfinder section Cassette tapes Up to performing the switch settings Basic proceduresFrom providing the power supply to loading the cassette Tape function buttons Procedure for shootingAdjust the white balance 3When adjusting the white balance on the spotEnsuring scene-to-scene continuity at other times Scene-to-scene continuityNews REC function SDC615 Scene-to-scene continuity during rec-pauseONE Shot Procedure for shooting in the on modesPRE-RECORDING function SDC905 Interval REC functionCheckpoints common to all Interval REC modes When the ONE Shot mode of Interval REC is toWhen the Interval REC mode is to be exited Procedure for shooting in the ONE Shot modeNormal playback and playback at different speeds When the Retake function is to be exitedRetake function Rec-review functionOutput CAM Adjusting the white balance and black balanceAdjusting the white balance White balance detection areaWhite balance memories When there is no time to adjust the white balanceWhen the white balance cannot be adjusted automatically Auto tracking white balance settingUse this to execute ABB Adjusting the black balanceBlack balance memory Viewfinder screen displays relating to the shutter Setting the electronic shutterSetting the shutter mode and speed Shutter modesItems to be set and what is set Selecting the recording signals and recording systemSetting the synchro scan mode Selecting the recording signalsSelecting the recording system Selecting the audio input signalsAdjusting the audio signal recording levels Concerning what is setUser bit memory function Setting the time dataSetting the user bits CTL Vtcg Time Date P-iRECRegion Setting the internal clock’s date and timeExternally locking the time code Setting the time codeTime code when the battery is replaced Operating procedure for external lockingExamples Setting the Umid informationConcerning the user bit setting during external lock To release the external lockBasic menu operations Menu configurationMenu displays on the viewfinder screen To set an item to on or OFF Selecting the user menusTo increment the value To decrement the valueSelecting the viewfinder screen display items Viewfinder screen status display configurationViewfinder screen status displays Viewfinder lamp displaysMode Check Display item What is displayed Status when display appearsButtons InformationAllocated to User Display White BAL switchFilter positions Cumulative gainZoom Zoom Mode CheckViewfinder screen display selection Setting change/adjustment result messages and display modes Setting the marker displaysSetting the camera ID Marker check screen displays Marker Select button function Mode check screen displays Mode Check button functionChecking the return video signal on the viewfinder Setting items and details Menu-driven function setupSetting the User SW Gain switching Selecting the video output signalsFunctions which can be selected Setting items and what is setSelecting the F.AUDIO Level control function Data handling Setting the color temperature manuallyHandling the setup card Selecting the file No Setup card operationsFormatting the setup card Saving the data settings on the cardGiving a title to the selected file Saving the data settings to the selected fileLoading the data of the selected file Loading the data saved on the cardLoading the user data How to use the user dataWriting the setting data in the user area Reading the setting data used for the scene files How to use the scene file dataWriting the setting data used for the scene files Scene Read User Data # Scene SEL Write Reset # Read Scene Read User Data Scene SEL Write Reset Operation method without performing File menu operations How to use the lens file dataWhite BAL switch Reference Supplying the powerAttaching the battery and setting the battery type Using the Anton Bauer battery packConnect here BP-90 type battery case Using the BP-90 type battery packBattery holder Label Surface NP-1 type Battery case Using the NP-1 type battery packUsing the V-mount type battery pack +12V Attaching the viewfinder and adjusting its positionUsing an AC power supply When the AJ-B75 AC adapter made by Panasonic is usedMark Attaching the lensLens socket Lever for Securing the lens Mount cap Approx meters Adjusting the lens flangeAdjusting the white shading of the lens Set the White BAL selector switch to a or B, Giving a title to the selected file no Storing the lens file dataReading the lens file data When using an external microphone Audio input signal preparationsWhen using the front microphone When using a UniSlot wireless receiver When using a wireless receiverWhen using an audio component When using an externally connected wireless receiverDetaching the unit from the tripod attachment Adjusting the position of the shoulder padMounting the unit on a tripod Attaching the shoulder beltExample showing use of the SHAN-RC700 rain cover Connecting the extension control unit AJ-EC3EAttaching the rain cover Attaching the Front Audio Level control knobInspecting the camera unit Inspections prior to shootingPreparation for inspections Tape travel inspection Automatic audio level adjustment function inspectionManual audio level adjustment function inspection Inspecting the VTR unitInspections relating to the time code and user bits Inspection using external microphonesSelf-diagnosis function Maintenance Push Connectors and signalsREC Warning Battery ENDSlack Tape ENDServo Wireless RFHumid Tape Near END Battery Near ENDError codes Error codes 81 to 92 relating to the Dvcpro connectorPush in and turn at Emergency ejectEmergency Eject screwHow to interpret the menu lists Menu configurationHow to open the menus RED System ModeCAM Option Mode 6SEC REC FunctionOn Memory ONE Shot26P EXT For Output SELGenlock INTMatrix 1 ROPColor Correction LOW Setting Black Strech MID SettingHigh Setting $ Master Gain=SKIN Tone Area Additional DTLDirection Flare For setting the Master GammaKNEE/LEVEL GammaVideo level Camera SettingsVF Displays Zebra pattern displayBAR VF INDICATOR1VF Marker User BOXSAVE&TAPE VF INDICATOR2Mode Check IND 7 !LEDShutter Select Camera IDShutter Speed Split SW ModeUser SW SmpteUser SW Gain White Balance ModeCard R/W Select FileIris Card READ/WRITEInitialize DiagnosticLens File System CheckReview Black ShadingWhite Shading VTR FunctionData storage Range BATTERY/TAPEBattery SETTING1 HYTRON120 END Battery SETTING25 MIC/AUDIO1 7 TC/UB 6 MIC/AUDIO2Umid SET/INFO VTR DiagID MIX INH Config DfltOption Audio System Video SystemAnalog component output Other Connectors Audio Output ConnectorsTime Code Input Connector Time Code Output ConnectorPanasonic Broadcast Europe Panasonic Marketing Europe GmbH
Top Page Image Contents