Panasonic DMC-TZ3EE, DMC-TZ3P manual Temporary cancellation of factory setting, Turn the Power on

Page 10

3.4.2.INITIAL SETTINGS:

When you replace the Main PCB, be sure to perform the initial settings after achieving the adjustment by ordering the following pro- cedure in accordance with model suffix of the unit.

1. IMPORTANT NOTICE:

Before proceeding Initial settings, be sure to read the following CAUTIONS.

2.PROCEDURES:

•Preparation. Proceed the picture back up from the unit (Refer to above "CAUTION 2")

•Step 1. The temporary cancellation of factory setting:

Set the mode dial to “[ Normal picture mode ] (Red camera mark)”.

While keep pressing [ Optical Image Stabilizer ] and “[ UP ] of Cross key” simultaneously, turn the Power on.

•Step 2. The cancellation of factory setting: Set the mode dial to “[ Playback ]”.

Press [ Optical Image Stabilizer ] and “[ UP ] of Cross key” simultaneously, then turn the Power off.

•Step 3. Turn the Power on:

Set the mode dial to “[ Normal picture mode ] (Red camera mark)”, and then turn the Power on.

•Step 4. Display the INITIAL SETTING:

While keep pressing [ MENU ] and “[ RIGHT ] of Cross key” simultaneously, turn the Power off.

10

Image 10

Contents Digital Camera Table of Contents Leakage Current Cold Check Safety PrecautionGeneral Guidelines Leakage Current Hot Check See FigureHow to Discharge the Capacitor on Flash PCB Fig. F1How to Recycle the Lithium Ion Battery U.S. Only Before Use How to Replace the Lithium Battery Replacement ProcedureIntroduction General Description About Lead Free Solder PbF Service NavigationRecommended Lead Free Solder Service Parts Route Important Notice 1Other than U.S.A. and Canadian MarketHow to Define the Model Suffix Ntsc or PAL model Defining methodsTurn the Power on Temporary cancellation of factory settingDisplay the Initial Setting Default setting After Initial Settings Set the Initial Setting Refer to CautionConfirmation Specifications Location of Controls and Components Page Service Mode Error Code Memory FunctionHow to read the error code OISHow to returned to Normal Display About * display in the above tableConfirm the version Confirmation of Firmware VersionPoint Service Fixture & Tools Service Fixture and ToolsWhen Replacing the Main PCB Service PositionExtension Cable Connections for DMC-TZ2 Disassembly and Assembly Instructions Disassembly Flow Chart PCB LocationDisassembly Procedure For DMC-TZ3For DMC-TZ2 Fig. D2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Disassembly Procedure for Lens Removal of the Battery CasePage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Unit Removal of the CCD Unit Removal of the Zoom MotorRemove the CCD unit except for replacing Grease apply point of lens unit are as follows Measurements and Adjustments Matrix Chart for Replaced Part and Necessary AdjustmentCleaning Lens and LCD Panel MaintenaceDiagrams and Replacement Parts List S1. About Indication of The Schematic DiagramS2. Block Diagram S2.1. Overall Block DiagramS3. Schematic Diagram S3.1. Interconnection DiagramS3.2. Flash Schematic Diagram 25ATop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 S3.7. Lens Flex Schematic Diagram Focus EncoderS4. Print Circuit Board S4.1. Flash P.C.BS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page S5. Replacement Parts List Important Safety NoticeRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6. Exploded View S6.1. Frame and Casing SectionS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section