Panasonic DMC-TZ3P, DMC-TZ3EB manual Disassembly Procedure for Lens, Removal of the Battery Case

Page 28

8.3.9.Removal of the Battery Case

Fig. D11

NOTE: (When Assembling)

Be sure to confirm the following points when assembling.

•The Screw is tightened enough.

•Assembling conditions are fine. (No distortion, no illegal- space.)

•No dust and/or dirt on every Lens surfaces.

•LCD image is fine. (No dust and dirt on it, and no gradient images.)

8.4.Disassembly Procedure for the

Lens

NOTE: When Disassembling and Assembling for the Lens

1.To minimize the possibility of the CCD being dirt, perform disassemble and/or assemble under the condition of the CCD is being mounted.

Disassembling procedures for the CCD unit, refer to item 8.6.

2.Take care that the dust and dirt are not entered into the lens.

In case of the dust is putted on the lens, blow off them by airbrush.

3.Do not touch the surface of lens.

4.Use lens cleaning KIT (BK)(VFK1900BK).

5.Apply the grease to the point where is shown to" Grease apply" in the figure.

8.4.1.Zoom Motor Unit and Master

Frange Unit

1.Unsolder (16 points).

2.Remove the libs (4 points).

3.Unscrew the 6 screws (A).

4.Remove the zoom motor unit.

5.Remove the master flange unit.

28

Image 28

Contents Digital Camera Table of Contents Safety Precaution General GuidelinesLeakage Current Cold Check Leakage Current Hot Check See FigureHow to Discharge the Capacitor on Flash PCB Fig. F1How to Recycle the Lithium Ion Battery U.S. Only Before Use How to Replace the Lithium Battery Replacement ProcedureService Navigation Recommended Lead Free Solder Service Parts RouteIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketHow to Define the Model Suffix Ntsc or PAL model Defining methodsTurn the Power on Temporary cancellation of factory settingDisplay the Initial Setting Default setting After Initial Settings Set the Initial Setting Refer to CautionConfirmation Specifications Location of Controls and Components Page Service Mode Error Code Memory FunctionHow to read the error code OISHow to returned to Normal Display About * display in the above tableConfirm the version Confirmation of Firmware VersionPoint Service Fixture & Tools Service Fixture and ToolsWhen Replacing the Main PCB Service PositionExtension Cable Connections for DMC-TZ2 Disassembly and Assembly Instructions Disassembly Flow Chart PCB LocationDisassembly Procedure For DMC-TZ3For DMC-TZ2 Fig. D2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Disassembly Procedure for Lens Removal of the Battery CasePage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Unit Removal of the CCD Unit Removal of the Zoom MotorRemove the CCD unit except for replacing Grease apply point of lens unit are as follows Measurements and Adjustments Matrix Chart for Replaced Part and Necessary AdjustmentCleaning Lens and LCD Panel MaintenaceDiagrams and Replacement Parts List S1. About Indication of The Schematic DiagramS2. Block Diagram S2.1. Overall Block DiagramS3. Schematic Diagram S3.1. Interconnection DiagramS3.2. Flash Schematic Diagram 25ATop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 S3.7. Lens Flex Schematic Diagram Focus EncoderS4. Print Circuit Board S4.1. Flash P.C.BS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page S5. Replacement Parts List Important Safety NoticeRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6. Exploded View S6.1. Frame and Casing SectionS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section