Panasonic DMC-TZ3EB, DMC-TZ3EE, DMC-TZ3PC manual Measurements and Adjustments

Page 37

9 Measurements and Adjustments

9.1.Matrix Chart for Replaced Part and Necessary Adjustment

The relation between Replaced part and Necessary Adjustment is shown in the following table. When concerned part is replaced, be sure to achieve the necessary adjustment(s).

As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.

The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/ VDBG-PAVC”.

NOTE:

After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.

				Replaced Part
		Main P.C.B.	VENUS	Flash-ROM	Lens Part	CCD Unit
	Adjustment Item		(IC6001)	(IC6002)	(Excluding
					CCD)

Camera	OIS hall element adjustment	O	O	O	O
Section	(OIS)

	Back focus adjustment	O	O	O	O
	(BF)

	Shutter adjustment	O	O	O	O	O
	(SHT)

	ISO sensitivity adjustment	O	O	O	O	O
	(ISO)

	AWB adjustment	O	O	O	O	O
	High brightness coloration inspection
	(WBL)

	CCD white scratch compensation	O	O	O		O
	(WKI)

NOTE:

*There is no LCD adjustment in this model.

*There is no CCD Black scratch compensation adjustment (BKI) in this model.

37

Image 37

Contents Digital Camera Table of Contents General Guidelines Safety PrecautionLeakage Current Cold Check Leakage Current Hot Check See FigureFig. F1 How to Discharge the Capacitor on Flash PCBHow to Recycle the Lithium Ion Battery U.S. Only Before Use Replacement Procedure How to Replace the Lithium BatteryRecommended Lead Free Solder Service Parts Route Service NavigationIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketDefining methods How to Define the Model Suffix Ntsc or PAL modelTurn the Power on Temporary cancellation of factory settingDisplay the Initial Setting Default setting After Initial Settings Set the Initial Setting Refer to CautionConfirmation Specifications Location of Controls and Components Page Error Code Memory Function Service ModeOIS How to read the error codeAbout * display in the above table How to returned to Normal DisplayConfirm the version Confirmation of Firmware VersionPoint Service Fixture and Tools Service Fixture & ToolsService Position When Replacing the Main PCBExtension Cable Connections for DMC-TZ2 Disassembly Flow Chart PCB Location Disassembly and Assembly InstructionsFor DMC-TZ3 Disassembly ProcedureFig. D2 For DMC-TZ2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Removal of the Battery Case Disassembly Procedure for LensPage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Unit Removal of the CCD Unit Removal of the Zoom MotorRemove the CCD unit except for replacing Grease apply point of lens unit are as follows Matrix Chart for Replaced Part and Necessary Adjustment Measurements and AdjustmentsMaintenace Cleaning Lens and LCD PanelS1. About Indication of The Schematic Diagram Diagrams and Replacement Parts ListS2.1. Overall Block Diagram S2. Block DiagramS3.1. Interconnection Diagram S3. Schematic Diagram25A S3.2. Flash Schematic DiagramTop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 Focus Encoder S3.7. Lens Flex Schematic DiagramS4.1. Flash P.C.B S4. Print Circuit BoardS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page Important Safety Notice S5. Replacement Parts ListRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6.1. Frame and Casing Section S6. Exploded ViewS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section