Panasonic DMC-TZ3PC, DMC-TZ3EB, DMC-TZ3EE manual Diagrams and Replacement Parts List

Page 39

DSC0703017CE/DSC0703019CE

Service Manual

Diagrams and Replacement

Parts List

Digital Camera

Model No.

 

DMC-TZ3EF

DMC-TZ2P

DMC-TZ2GD

DMC-TZ2PC

DMC-TZ2GK

DMC-TZ3EG

DMC-TZ2PL

DMC-TZ2GN

DMC-TZ3EGM

DMC-TZ2EB

DMC-TZ2GT

DMC-TZ3GC

DMC-TZ2EE

DMC-TZ3P

DMC-TZ3GD

DMC-TZ2EF

DMC-TZ3PC

DMC-TZ3GK

DMC-TZ2EG

DMC-TZ3PL

DMC-TZ3GN

DMC-TZ2EGM

DMC-TZ3EB

DMC-TZ3GT

DMC-TZ2GC

DMC-TZ3EE

DMC-TZ3SG

Vol. 1

Colour

(S)...........Silver Type

(K)...........Black Type (except DMC-TZ2PL/GD/GT)

(A)...........Blue Type (only DMC-TZ3P/PC/EB/EE/EF/EG/EGM/GC/SG)

S1. About Indication of The Schematic Diagram

S1.1. Important Safety Notice

COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.

1.Although reference number of the parts is indicated on the P.C.B. drawing and/or schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.

2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B. when the TP (Test Point) indicated as "" mark.

3.The voltage being indicated on the schematic diagram is measured in "Standard-Playback" mode when there is no specify mode is mentioned.

4.Although the voltage and waveform available on here is measured with standard frame, it may be differ from actual measurement due to modification of circuit and so on.

5.The voltage being indicated here may be include observational-error (deviation) due to internal-resistance and/or reactance of equipment. Therefore, handle the value indicated on here as reference.

6.Use the parts number indicated on the Replacement Parts List .

7.Indication on Schematic diagrams:

 

Circuit name being connected.

 

 

 

OFTR

FEP

This signal is connected

 

 

to the FEP schematic diagram.

Name of Signal

 

 

Table of contents

S1. About Indication of The Schematic Diagram

S-1

S4.4. CCD Flex P.C.B. (DMC-TZ2)

S-11

S1.1. Important Safety Notice

S-1

S4.5. CCD Flex P.C.B. (DMC-TZ3)

S-12

S2. Block Diagram

S-2

S4.6. Lens Flex P.C.B

S-13

 

 

S2.1. Overall Block Diagram

S-2

S5. Replacement Parts List

S-15

S3. Schematic Diagram

S-3

S6. Exploded View

S-20

S3.1. Interconnection Diagram

S-3

S6.1. Frame and Casing Section

S-20

S3.2. Flash Schematic Diagram

S-4

S6.2. Packing Parts and Accessories Section (1)

S-21

S3.3. Top Operation Schematic Diagram

S-5

S6.3. Packing Parts and Accessories Section (2)

S-22

S3.4. AF Assist Schematic Diagram

S-5

 

 

S3.5. CCD Flex Schematic Diagram (DMC-TZ2)

S-6

 

 

S3.6. CCD Flex Schematic Diagram (DMC-TZ3)

S-7

 

 

S3.7. Lens Flex Schematic Diagram

S-8

 

 

S4. Print Circuit Board

S-9

 

 

S4.1. Flash P.C.B

S-9

 

 

S4.2. Top Operation P.C.B

S-10

 

 

S4.3. AF Assist P.C.B

S-10

 

 

S-1

Image 39
Contents Digital Camera Table of Contents Leakage Current Hot Check See Figure Safety PrecautionGeneral Guidelines Leakage Current Cold CheckFig. F1 How to Discharge the Capacitor on Flash PCBHow to Recycle the Lithium Ion Battery U.S. Only Before Use Replacement Procedure How to Replace the Lithium BatteryImportant Notice 1Other than U.S.A. and Canadian Market Service NavigationRecommended Lead Free Solder Service Parts Route Introduction General Description About Lead Free Solder PbFDefining methods How to Define the Model Suffix Ntsc or PAL modelTemporary cancellation of factory setting Turn the Power onDisplay the Initial Setting Set the Initial Setting Refer to Caution Default setting After Initial SettingsConfirmation Specifications Location of Controls and Components Page Error Code Memory Function Service ModeOIS How to read the error codeAbout * display in the above table How to returned to Normal DisplayConfirmation of Firmware Version Confirm the versionPoint Service Fixture and Tools Service Fixture & ToolsService Position When Replacing the Main PCBExtension Cable Connections for DMC-TZ2 Disassembly Flow Chart PCB Location Disassembly and Assembly InstructionsFor DMC-TZ3 Disassembly ProcedureFig. D2 For DMC-TZ2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Removal of the Battery Case Disassembly Procedure for LensPage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Removal of the CCD Unit Removal of the Zoom Motor UnitRemove the CCD unit except for replacing Grease apply point of lens unit are as follows Matrix Chart for Replaced Part and Necessary Adjustment Measurements and AdjustmentsMaintenace Cleaning Lens and LCD PanelS1. About Indication of The Schematic Diagram Diagrams and Replacement Parts ListS2.1. Overall Block Diagram S2. Block DiagramS3.1. Interconnection Diagram S3. Schematic Diagram25A S3.2. Flash Schematic DiagramTop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 Focus Encoder S3.7. Lens Flex Schematic DiagramS4.1. Flash P.C.B S4. Print Circuit BoardS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page Important Safety Notice S5. Replacement Parts ListRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6.1. Frame and Casing Section S6. Exploded ViewS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section