Panasonic DMC-TZ3EB, DMC-TZ3EE, DMC-TZ3PC manual When Replacing the Main PCB, Service Position

Page 20

7.2.When Replacing the Main PCB

After replacing the MAIN PCB, be sure to achieve adjustment.

The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in “TSN system”, together with Maintenance software.

7.3.Service Position

This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.

		Table S1 Extension Cable List

No.	Parts No.	Connection	Form
1	VFK1950	FP9801 (MAIN) - CCD UNIT	33PIN 0.3 FFC
2	RFKZ0416	FP9802 (MAIN) - LENS UNIT	41PIN 0.3 FFC

3	RFKZ0363	FP9803 (SUB) - FP9901 (FLASH)	19PIN 0.5 FFC
4	RFKZ0363	FP9005 (MAIN) - FP8001 (TOP OPERATION)	19PIN 0.5 FFC

5	RFKZ0363	FP9001 (MAIN) - LCD UNIT (For DMC-TZ3)	19PIN 0.5 FFC
		FP9002 (MAIN) - LCD UNIT (For DMC-TZ2)
6	VFK1974	FP9003 (MAIN) - LCD UNIT (For DMC-TZ3)	4PIN 0.5 FFC

		FP9004 (MAIN) - LCD UNIT (For DMC-TZ2)
7	RFKZ0362	PS9801 (SUB) - PP9001 (MAIN)	100PIN B to B

7.3.1.Extension Cable Connections for DMC-TZ3

20

Image 20

Contents Digital Camera Table of Contents Safety Precaution General GuidelinesLeakage Current Cold Check Leakage Current Hot Check See FigureHow to Discharge the Capacitor on Flash PCB Fig. F1How to Recycle the Lithium Ion Battery U.S. Only Before Use How to Replace the Lithium Battery Replacement ProcedureService Navigation Recommended Lead Free Solder Service Parts RouteIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketHow to Define the Model Suffix Ntsc or PAL model Defining methodsDisplay the Initial Setting Temporary cancellation of factory settingTurn the Power on Confirmation Set the Initial Setting Refer to CautionDefault setting After Initial Settings Specifications Location of Controls and Components Page Service Mode Error Code Memory FunctionHow to read the error code OIS How to returned to Normal Display About * display in the above tablePoint Confirmation of Firmware VersionConfirm the version Service Fixture & Tools Service Fixture and ToolsWhen Replacing the Main PCB Service PositionExtension Cable Connections for DMC-TZ2 Disassembly and Assembly Instructions Disassembly Flow Chart PCB LocationDisassembly Procedure For DMC-TZ3For DMC-TZ2 Fig. D2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Disassembly Procedure for Lens Removal of the Battery CasePage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Remove the CCD unit except for replacing Removal of the CCD Unit Removal of the Zoom MotorUnit Grease apply point of lens unit are as follows Measurements and Adjustments Matrix Chart for Replaced Part and Necessary AdjustmentCleaning Lens and LCD Panel MaintenaceDiagrams and Replacement Parts List S1. About Indication of The Schematic DiagramS2. Block Diagram S2.1. Overall Block DiagramS3. Schematic Diagram S3.1. Interconnection DiagramS3.2. Flash Schematic Diagram 25ATop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 S3.7. Lens Flex Schematic Diagram Focus EncoderS4. Print Circuit Board S4.1. Flash P.C.BS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page S5. Replacement Parts List Important Safety NoticeRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6. Exploded View S6.1. Frame and Casing SectionS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section