Panasonic DMC-TZ3P Service Navigation, Important Notice 1Other than U.S.A. and Canadian Market

Page 8

3 Service Navigation

3.1.Introduction

This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

3.2.General Description About Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the normal solder.

Distinction of PCB Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)

•The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

•To put lead free solder, it should be well molten and mixed with the original lead free solder.

•Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

•Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the lead free solder.

•Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01K

-----------(0.3mm 100g Reel)

RFKZ06D01K

-----------(0.6mm 100g Reel)

RFKZ10D01K

-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

3.3.Important Notice 1:(Other than U.S.A. and Canadian Market)

1.The service manual does not contain the following information, because of the impossibility of servicing at component level without concerned equipment/facilites.

a.Schematic diagram, Block Diagram and PCB layout of MAIN PCB.

b.Parts list for individual parts for MAIN PCB.

When a part replacement is required for repairing MAIN PCB, replace as an assembled parts. (Main PCB)

2.The following category is/are recycle module part. please send it/them to Central Repair Center.

•MAIN PCB (TZ3: VEP56047A/TZ2: VEP56047B)

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Digital Camera Table of Contents Safety Precaution General GuidelinesLeakage Current Cold Check Leakage Current Hot Check See FigureHow to Discharge the Capacitor on Flash PCB Fig. F1 How to Recycle the Lithium Ion Battery U.S. Only Before Use How to Replace the Lithium Battery Replacement ProcedureService Navigation Recommended Lead Free Solder Service Parts RouteIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketHow to Define the Model Suffix Ntsc or PAL model Defining methodsDisplay the Initial Setting Temporary cancellation of factory settingTurn the Power on Confirmation Set the Initial Setting Refer to CautionDefault setting After Initial Settings Specifications Location of Controls and Components Page Service Mode Error Code Memory FunctionHow to read the error code OISHow to returned to Normal Display About * display in the above tablePoint Confirmation of Firmware VersionConfirm the version Service Fixture & Tools Service Fixture and ToolsWhen Replacing the Main PCB Service PositionExtension Cable Connections for DMC-TZ2 Disassembly and Assembly Instructions Disassembly Flow Chart PCB LocationDisassembly Procedure For DMC-TZ3For DMC-TZ2 Fig. D2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Disassembly Procedure for Lens Removal of the Battery CasePage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Remove the CCD unit except for replacing Removal of the CCD Unit Removal of the Zoom MotorUnit Grease apply point of lens unit are as follows Measurements and Adjustments Matrix Chart for Replaced Part and Necessary AdjustmentCleaning Lens and LCD Panel MaintenaceDiagrams and Replacement Parts List S1. About Indication of The Schematic DiagramS2. Block Diagram S2.1. Overall Block DiagramS3. Schematic Diagram S3.1. Interconnection DiagramS3.2. Flash Schematic Diagram 25ATop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 S3.7. Lens Flex Schematic Diagram Focus EncoderS4. Print Circuit Board S4.1. Flash P.C.BS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page S5. Replacement Parts List Important Safety NoticeRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6. Exploded View S6.1. Frame and Casing SectionS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section
Top Page Image Contents