Panasonic DMC-TZ3PC, DMC-TZ3EB, DMC-TZ3EE manual Service Mode, Error Code Memory Function

Page 15

6 Service Mode

6.1.Error Code Memory Function

1.General description

This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.

The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off.

2.How to display

The error code can be displayed by the following procedure:

Before perform the error code memory function, connect the AC adaptor or insert the battery.

(Since this unit has built-in memory, this error code memory function can be performed without inserting SD card.)

•1. The temporary cancellation of factory setting:

Set the mode dial to “[ Normal picture mode ] (Red camera mark)”.

While keep pressing [ Optical Image Stabilizer Button ] and “[ UP ] of Cross key” simultaneously, turn the Power on.

•2. The display of error code:

Press [ Optical Image Stabilizer Button ], [ MENU ] and “[ LEFT ] of Cross key” simultaneously with the step 1 condition. The display is changed as shown below when the above buttons is pressed simultaneously.

Normal display → Error code display → Operation history display → Normal display → .....

Example of Error Code Display

•3. The change of display:

The error code can be memorized 16 error codes in sequence, however it is displayed 5 errors on the LCD. Display can be changed by the following procedure:

“[ UP ] or [ DOWN ] of Cross key” : It can be scroll up or down one.

“[ LEFT ] or [ RIGHT ] of Cross key” : It can be display last 5 error or another 5 error.

•4. How to read the error date:

The error date code is displayed from the left in order at the month, year, day, time.

Error date information is acquired from "Clock setting" information when the error occurs. When the clock is not setting, it is displayed as “00000000”.

15

Image 15

Contents Digital Camera Table of Contents Leakage Current Hot Check See Figure Safety PrecautionGeneral Guidelines Leakage Current Cold CheckFig. F1 How to Discharge the Capacitor on Flash PCBHow to Recycle the Lithium Ion Battery U.S. Only Before Use Replacement Procedure How to Replace the Lithium BatteryImportant Notice 1Other than U.S.A. and Canadian Market Service NavigationRecommended Lead Free Solder Service Parts Route Introduction General Description About Lead Free Solder PbFDefining methods How to Define the Model Suffix Ntsc or PAL modelTemporary cancellation of factory setting Turn the Power onDisplay the Initial Setting Set the Initial Setting Refer to Caution Default setting After Initial SettingsConfirmation Specifications Location of Controls and Components Page Error Code Memory Function Service ModeOIS How to read the error codeAbout * display in the above table How to returned to Normal DisplayConfirmation of Firmware Version Confirm the versionPoint Service Fixture and Tools Service Fixture & ToolsService Position When Replacing the Main PCBExtension Cable Connections for DMC-TZ2 Disassembly Flow Chart PCB Location Disassembly and Assembly InstructionsFor DMC-TZ3 Disassembly ProcedureFig. D2 For DMC-TZ2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Removal of the Battery Case Disassembly Procedure for LensPage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Removal of the CCD Unit Removal of the Zoom Motor UnitRemove the CCD unit except for replacing Grease apply point of lens unit are as follows Matrix Chart for Replaced Part and Necessary Adjustment Measurements and AdjustmentsMaintenace Cleaning Lens and LCD PanelS1. About Indication of The Schematic Diagram Diagrams and Replacement Parts ListS2.1. Overall Block Diagram S2. Block DiagramS3.1. Interconnection Diagram S3. Schematic Diagram25A S3.2. Flash Schematic DiagramTop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 Focus Encoder S3.7. Lens Flex Schematic DiagramS4.1. Flash P.C.B S4. Print Circuit BoardS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page Important Safety Notice S5. Replacement Parts ListRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6.1. Frame and Casing Section S6. Exploded ViewS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section