Panasonic DMC-TZ3EB, DMC-TZ3EE, DMC-TZ3PC manual S2. Block Diagram, S2.1. Overall Block Diagram

Page 40

S2. Block Diagram

S2.1. Overall Block Diagram

	(28mm ~ 280mm)
				IC3101	IC3001
				CCD	IC3001
				CCD	PRE PROCESS
				1/2.33" 7 MEGA PIX	PRE PROCESS
				1/2.33" 7 MEGA PIX	CDS,AGC,
				[DMC-TZ2]	CDS,AGC,
				1/2.35" 8 MEGA PIX	A/D,TG,
				[DMC-TZ3]	CCD DRIVER
ZOOM	IRIS	SHUTTER	OIS UNIT	FOCUS
			IC7001
			MOTOR DRIVE,
			OIS DRIVE&
			PRE PROCESS
				IC7201
				GYRO
				SENSOR X/Y
FLASH
REAR OPERATION UNIT
				IC9101
				SYSTEM IC
				X9101
				(32.768kHz)
					IC6002
					FLASH ROM/
					128Mbit
TOP OPERATION UNIT

IC6001

VENUS3

CAMERA PROCESS

J-PEG COMP/EX PANDS

MEDIA I/F

USB I/F

MAIN MICROPROCESSOR

OIS CONTROL

LENS DRIVE

LCD DRIVE

	IC6003
	SDRAM/128Mbit
	[DMC-TZ2]
	SDRAM/256Mbit
	[DMC-TZ3]
	SD
	CARD
	IC5001	MICROPHONE
	AUDIO AMP
	MICROPHONE AMP	SPEAKER
	SPEAKER CONTROL	SPEAKER
	IC9003	DIGITAL/ AV OUT
	VIDEO OUT	TERMINAL
		COLOR LCD
	IC4001	PANEL
	IC4001	2.5" PANEL 207K PIX
	LCD DRIVE	2.5" PANEL 207K PIX
		[DMC-TZ2]
		3.0" PANEL 230K PIX
		[DMC-TZ3]
		DC IN TERMINAL
	IC1001
	POWER
	(POWER SUPPLY)
		BATTERY

DMC-TZ3/TZ2 OVERALL BLOCK DIAGRAM

S-2

Image 40

Contents Digital Camera Table of Contents Safety Precaution General GuidelinesLeakage Current Cold Check Leakage Current Hot Check See FigureHow to Discharge the Capacitor on Flash PCB Fig. F1How to Recycle the Lithium Ion Battery U.S. Only Before Use How to Replace the Lithium Battery Replacement ProcedureService Navigation Recommended Lead Free Solder Service Parts RouteIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketHow to Define the Model Suffix Ntsc or PAL model Defining methodsTurn the Power on Temporary cancellation of factory settingDisplay the Initial Setting Default setting After Initial Settings Set the Initial Setting Refer to CautionConfirmation Specifications Location of Controls and Components Page Service Mode Error Code Memory FunctionHow to read the error code OISHow to returned to Normal Display About * display in the above tableConfirm the version Confirmation of Firmware VersionPoint Service Fixture & Tools Service Fixture and ToolsWhen Replacing the Main PCB Service PositionExtension Cable Connections for DMC-TZ2 Disassembly and Assembly Instructions Disassembly Flow Chart PCB LocationDisassembly Procedure For DMC-TZ3For DMC-TZ2 Fig. D2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Disassembly Procedure for Lens Removal of the Battery CasePage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Unit Removal of the CCD Unit Removal of the Zoom MotorRemove the CCD unit except for replacing Grease apply point of lens unit are as follows Measurements and Adjustments Matrix Chart for Replaced Part and Necessary AdjustmentCleaning Lens and LCD Panel MaintenaceDiagrams and Replacement Parts List S1. About Indication of The Schematic DiagramS2. Block Diagram S2.1. Overall Block DiagramS3. Schematic Diagram S3.1. Interconnection DiagramS3.2. Flash Schematic Diagram 25ATop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 S3.7. Lens Flex Schematic Diagram Focus EncoderS4. Print Circuit Board S4.1. Flash P.C.BS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page S5. Replacement Parts List Important Safety NoticeRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6. Exploded View S6.1. Frame and Casing SectionS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section