Panasonic DMC-TZ3EB, DMC-TZ3P, DMC-TZ3EE manual How to Recycle the Lithium Ion Battery U.S. Only

Page 5

2 Warning

2.1.Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).

1.Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2.After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi- num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4.Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can generate electrical charge sufficient to damage ES devices.

5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara- ble conductive material).

7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8.Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf- ficient to damage an ES device).

2.2.How to Recycle the Lithium Ion Battery (U.S. Only)

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Digital Camera Table of Contents General Guidelines Safety PrecautionLeakage Current Cold Check Leakage Current Hot Check See FigureFig. F1 How to Discharge the Capacitor on Flash PCBHow to Recycle the Lithium Ion Battery U.S. Only Before Use Replacement Procedure How to Replace the Lithium BatteryRecommended Lead Free Solder Service Parts Route Service NavigationIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketDefining methods How to Define the Model Suffix Ntsc or PAL modelDisplay the Initial Setting Temporary cancellation of factory settingTurn the Power on Confirmation Set the Initial Setting Refer to CautionDefault setting After Initial Settings Specifications Location of Controls and Components Page Error Code Memory Function Service ModeOIS How to read the error codeAbout * display in the above table How to returned to Normal DisplayPoint Confirmation of Firmware VersionConfirm the version Service Fixture and Tools Service Fixture & ToolsService Position When Replacing the Main PCBExtension Cable Connections for DMC-TZ2 Disassembly Flow Chart PCB Location Disassembly and Assembly InstructionsFor DMC-TZ3 Disassembly ProcedureFig. D2 For DMC-TZ2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Removal of the Battery Case Disassembly Procedure for LensPage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Remove the CCD unit except for replacing Removal of the CCD Unit Removal of the Zoom MotorUnit Grease apply point of lens unit are as follows Matrix Chart for Replaced Part and Necessary Adjustment Measurements and AdjustmentsMaintenace Cleaning Lens and LCD PanelS1. About Indication of The Schematic Diagram Diagrams and Replacement Parts ListS2.1. Overall Block Diagram S2. Block DiagramS3.1. Interconnection Diagram S3. Schematic Diagram25A S3.2. Flash Schematic DiagramTop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 Focus Encoder S3.7. Lens Flex Schematic DiagramS4.1. Flash P.C.B S4. Print Circuit BoardS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page Important Safety Notice S5. Replacement Parts ListRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6.1. Frame and Casing Section S6. Exploded ViewS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section
Top Page Image Contents