Panasonic DMC-TZ3EB, DMC-TZ3P, DMC-TZ3EE manual S5. Replacement Parts List, Important Safety Notice

Page 53

S5. Replacement Parts List

Note: 1.* Be sure to make your orders of replacement parts according to this list.

2.IMPORTANT SAFETY NOTICE

Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type.

3.Unless otherwise specified,

All resistors are in OHMS, K=1,000 OHMS. All capacitors are in MICRO-FARADS (uf), P=uuF.

4.The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available.

E.S.D. standards for Electrostatically Sensitive Devices, refer to “PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES” section.

Definition of Parts supplier:

1.Parts marked with [MBI] in the remarks column are supplied from “Matsushita Battery Industrial Co., Ltd.”

S-15

Image 53

Contents Digital Camera Table of Contents General Guidelines Safety PrecautionLeakage Current Cold Check Leakage Current Hot Check See FigureFig. F1 How to Discharge the Capacitor on Flash PCBHow to Recycle the Lithium Ion Battery U.S. Only Before Use Replacement Procedure How to Replace the Lithium BatteryRecommended Lead Free Solder Service Parts Route Service NavigationIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketDefining methods How to Define the Model Suffix Ntsc or PAL modelDisplay the Initial Setting Temporary cancellation of factory settingTurn the Power on Confirmation Set the Initial Setting Refer to CautionDefault setting After Initial Settings Specifications Location of Controls and Components Page Error Code Memory Function Service ModeOIS How to read the error codeAbout * display in the above table How to returned to Normal DisplayPoint Confirmation of Firmware VersionConfirm the version Service Fixture and Tools Service Fixture & ToolsService Position When Replacing the Main PCBExtension Cable Connections for DMC-TZ2 Disassembly Flow Chart PCB Location Disassembly and Assembly InstructionsFor DMC-TZ3 Disassembly ProcedureFig. D2 For DMC-TZ2Removal of the Main P.C.B Removal of the Lens Unit Removal of the Sub P.C.B Fig. D9 Removal of the Battery Case Disassembly Procedure for LensPage Removal of the Drive Frame Frame and Both Side Cam Page Page Assembly for the Zoom Motor Unit and Master Flange Unit Remove the CCD unit except for replacing Removal of the CCD Unit Removal of the Zoom MotorUnit Grease apply point of lens unit are as follows Matrix Chart for Replaced Part and Necessary Adjustment Measurements and AdjustmentsMaintenace Cleaning Lens and LCD PanelS1. About Indication of The Schematic Diagram Diagrams and Replacement Parts ListS2.1. Overall Block Diagram S2. Block DiagramS3.1. Interconnection Diagram S3. Schematic Diagram25A S3.2. Flash Schematic DiagramTop Operation AF Assist Schematic Diagram S3.5. CCD Flex Schematic Diagram DMC-TZ2 S3.6. CCD Flex Schematic Diagram DMC-TZ3 Focus Encoder S3.7. Lens Flex Schematic DiagramS4.1. Flash P.C.B S4. Print Circuit BoardS4.2. Top Operation P.C.B. / S4.3. AF Assist P.C.B S4.4. CCD Flex P.C.B. DMC-TZ2 S4.5. CCD Flex P.C.B. DMC-TZ3 S4.6. Lens Flex P.C.B Page Important Safety Notice S5. Replacement Parts ListRef.No Part Name & Description Pcs Remarks Speaker ML614S/ZT Battery Ref.No Part Name & Description Camera BAG DE-A45BA Battery Charger S6.1. Frame and Casing Section S6. Exploded ViewS6.2. Packing Parts and Accessories Section S6.3. Packing Parts and Accessories Section