Samsung user manual Installing the SPD-1000 Wall Mount

Page 15

Installation

Installing the SPD-1000 Wall Mount

1.Prepare the accessories in the camera box (power adapter, BNC auxiliary cable, 1 loose-proof screw, 2 installation brackets, installation cover) and the wall mount (STB-280PW or STB-230PW) and 3 installation bracket fixing screws in the mount packaging box.

power adapter(DC 12V, Peak 4A)

BNC auxiliary cable

2 installation brackets

3.Fix the wall bracket and the wall surface attachment installation bracket onto the wall mount (STB-280PW) with the screws supplied, as shown in the figure on the right, and connect the external incoming cables (video cable, controller cable and power cord) to the camera.

Wall

1 loose-
proof screw	installation cover	STB-280PW

2. Fix the wall mount (STB-280PW) with 3 screws to the wall where the camera is to be installed, as shown in the figure on the right.

Notes

*Precautions before Attaching the Installation Template

STB-230PW

Wall

4.Assemble the camera, which should already have been attached to the product installation bracket, to the wall attachment installation bracket, facing forwards, and fix the camera with the supplied fixing screw.

Wall

•Installation Place: Check that the function and performance of the camera installed on the wall will not be adversely affected by the external environment, and that the ceiling can adequately support the weight of the camera.

•Installation Direction: Determine the main direction of the camera in advance and attach the template so that the front of the template is in line with the camera direction.

•Caution: Since there is a danger of the product falling during installation, take care not to allow anyone to stand below the installation area.

28

29

Image 15

Contents English Page Features Contents Persons is not recommended PrecautionsMain Body Port Block Rear panel BodySetting Baud Rate Based on DVR Model Camera Initial SettingsOn the Path Setting RS-485 TerminationSetting Camera ID Switch SW2 #7 SW2 #8SW1-#1 SW1-#2 SW1-#3 SW1-#4 SW1-#5 SW1-#6 SW1-#7 SW1-#8 100 SW1-#1 SW1-#2 SW1-#3 SW1-#4 SW1-#5 SW1-#6 SW1-#7 SW1-#8 150 +12V Output Port Setting Termination ResistanceAuxiliary Video Out Port Pin Order Pin Name Purpose Following products are provided separately Installation Products Sold Separately Preparation for CableWall MountSTB-230PW Cable Connection Installation of SPD-1000Camera holder Connect the Power Adapter’s plug to the Power Wall Mount STB-280PWInstalling the SPD-1000 on a Ceiling To complete installation, rotateInstallation cover along the groove Installing the SPD-1000 Wall Mount Exposure Installing the Dome Housing STH-1000PIFunctional Description OSD Menu OrganizationON/OFF Zoom Tracking PTZ Camera User Menu SettingsCamera Setting Main MenuCamera exposure can be controlled WB ModeWhite Balance ExposureNo noise reduction effect Back LightSsnr Samsung Super Noise Reduction Sens-UpCamera Setting Ohter Day & NightOthers Sequence Setting Sequence Setting MenuSelect the Preset number Set up the Zoom and Focus Clear SettingTrace T SettingTime can be set up by the unit of 1-59 SEC and 1-59 MIN Pan 350˚ Auto Run in Pan directionTo enter the area name. a maximum of 12 letters English Chinese, numbers can be entered. When you finish inputtingName, adjust the position mark to SET using the joystick Area NameCamera Name Camera name is set up OSD SettingPreset Name Preset NameON/OFF Alarm is enabled in on mode Alarm SettingInput 1, Input 2 Alarm Input Mode/Priority/Method is set up Preset/Swing/Group/Tour/Trace/A.PANInitialization Menu Status of dome camera setting is displayedInitialize StatusProduct Structure Specifications Installation 2 Mini PTZ Dome Camera ControlAuto/Manual1/50~1/120000 Declaration of Conformity