Samsung Cable Connection Installation of SPD-1000, Wall Mount STB-280PW, Wall MountSTB-230PW

Page 13

Installation

Cable Connection

Installation of SPD-1000

1.First, connect one end of the BNC video cable connector to the Video Output Terminal.

2.Next, connect the other end of the connector to the Video Input Terminal of the monitor.

Monitor

In Terminal

Monitor

DATA BOX

Video Out Terminal

•Precautions for Installation

-Check that the installation location can safely bear four times the weight of the camera and its installation fittings.

-When fixing the ceiling installation bracket, use the supplied installation template and fixing screws.

-Take care not to drop the product during installation. Do not allow anyone to stand below the installation area.

• Optional Products for Installation

3. Connect the Controller Connection Terminal

of SPD-1000 and the external

Controller.

Controller

Controller Connection Terminal

1) Wall Mount (STB-280PW)

This housing is used to install the camera on an indoor wall or ceiling using an external conduit.

2) Wall Mount(STB-230PW)

4.Then, connect the Power Adapter Cable. Use a driver (-) to screw one part of the Power Adapter consisting of two lines to the Power Input Terminal of

the camera holder.

5. Connect the Power
Adapter’s plug to the Power	Power Adapter
Outlet.

This housing is used to install the camera on an indoor wall.

3) Dome Housing (STH-1000PI)

This housing is used to install the camera in a location that is dusty, or a place where extra protection for the camera is required.

4) Outdoor Housing (STH-1000PO)

This housing is used to install the camera at outdoor area

24

25

Image 13

Contents English Page Features Contents Persons is not recommended PrecautionsMain Body Port Block Rear panel BodySetting Baud Rate Based on DVR Model Camera Initial SettingsSetting Camera ID Switch Setting RS-485 TerminationSW2 #7 SW2 #8 On the PathSW1-#1 SW1-#2 SW1-#3 SW1-#4 SW1-#5 SW1-#6 SW1-#7 SW1-#8 100 SW1-#1 SW1-#2 SW1-#3 SW1-#4 SW1-#5 SW1-#6 SW1-#7 SW1-#8 150 Auxiliary Video Out Port Setting Termination ResistancePin Order Pin Name Purpose +12V Output PortProducts Sold Separately InstallationPreparation for Cable Following products are provided separatelyCamera holder Connect the Power Adapter’s plug to the Power Cable Connection Installation of SPD-1000Wall Mount STB-280PW Wall MountSTB-230PWTo complete installation, rotate Installing the SPD-1000 on a CeilingInstallation cover along the groove Installing the SPD-1000 Wall Mount Functional Description Installing the Dome Housing STH-1000PIOSD Menu Organization ExposureON/OFF Camera Setting PTZ Camera User Menu SettingsMain Menu Zoom TrackingWhite Balance WB ModeExposure Camera exposure can be controlledSsnr Samsung Super Noise Reduction Back LightSens-Up No noise reduction effectDay & Night Camera Setting OhterOthers Sequence Setting Menu Sequence SettingSelect the Preset number Set up the Zoom and Focus Clear SettingTime can be set up by the unit of 1-59 SEC and 1-59 MIN T SettingPan 350˚ Auto Run in Pan direction TraceName, adjust the position mark to SET using the joystick Chinese, numbers can be entered. When you finish inputtingArea Name To enter the area name. a maximum of 12 letters EnglishCamera Name Camera name is set up OSD SettingPreset Name Preset NameInput 1, Input 2 Alarm Input Mode/Priority/Method is set up Alarm SettingPreset/Swing/Group/Tour/Trace/A.PAN ON/OFF Alarm is enabled in on modeInitialize Status of dome camera setting is displayedStatus Initialization MenuProduct Structure Installation 2 Mini PTZ Dome Camera Control SpecificationsAuto/Manual1/50~1/120000 Declaration of Conformity