Axis Communications Q1615 Network Connector, Power Connector, Audio Connector, SD Card Slot

Page 7

AXIS Q1615 Network Camera

Hardware Overview

Network Connector

RJ45 Ethernet connector. Supports Power over Ethernet (PoE).

NOTICE

Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. All cables connecting the product to the network and that are routed outdoors or in demanding electrical environments shall be intended for their specific use. Make sure that the network devices

are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .

I/O Connector

Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to the 0 V DC reference point and power (DC output), the I/O connector provides the interface to:

•Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

•Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Power Connector

2-pin terminal block for power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.

Mini DC connector. Use the supplied adapter.

Audio Connector

The Axis product has the following audio connectors:

•Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

•Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier . A stereo connector must be used for audio out.

RS485/RS422 Connector

Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as PTZ devices.

SD Card Slot

A microSD card (not included) can be used for local recording with removable storage. For more information, see Technical Specifications on page 64.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Note

For SD card recommendations see www.axis.com

Control Button

The control button is used for:

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Axis Q1615 Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q1615 Network Camera Table of ContentsConnectors Performance Considerations TroubleshootingFor technical specifications, see Connectors and ButtonsHardware Overview Audio Connector Network ConnectorConnector Power ConnectorColor Indication LED IndicatorsStatus LED Behavior for Focus Assistant Function ButtonLens Buzzer Signal for Focus AssistantReplacing the lens BuzzerAxis Q1615 Network Camera Set the Root Password Accessing the ProductAccess from a Browser Access from the InternetControls on the Live View Set Power Line FrequencyConfigure Capture Mode Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerAMC Audio Controls PTZ ControlsMedia Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsBasic Setup Setting Up the ProductAdjust Focus Focus Assistant Image Video and AudioVideo Stream Pixel CounterStream Profiles Click Save to apply the new settings264 View Area Camera SettingsCapture Mode Go to Setup Video & Audio Camera SettingsWide Dynamic Range Image AppearanceImage Correction White BalanceShutter & Gain Exposure SettingsSet Shutter to View Area Go to Video & Audio Overlay Image OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabGo to Events Action Rules Privacy MaskFocus Use Overlay Text in an Action RuleBasic Audio SettingsAudio Modes Audio InputAudio Output Audio ClipsAxis Q1615 Network Camera Browser Viewer Description Live View ConfigDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsGuard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControls Operator Same as administrator but with lower priorityAdvanced Control QueueShock Detection DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection Windows15% 60-90% 75-95% Default valuesAudio Detection Recommended valuesApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q1615 Network Camera Hardware Input SignalEvents DetectorsTime Setting Up an Action RuleConvert Event Types to Action Rules SystemUse with action RecipientsGo to Events Action Rules and click Add RecipientGo to Events Schedules and click Add Setting Up an Email RecipientSchedules Go to Events Recipients and click AddGo to Events Recurrences and click Add RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Date & Time To install a self-signed certificateGo to Setup System Options Security Certificates Click Install certificate and upload the certificateNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Network Share StoragePorts & Devices SD CardPort Status MaintenanceLED Indicators COM PortLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis Q1615 Network Camera Upgrading the Firmware TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserSetup Video & Audio Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Audio output Function/group Specifications Audio Audio streamingSpecification Network Security Audio inputWeight Function/group SpecificationsPower ConnectorsSetup example ConnectorsConnector Function Pin SpecificationsAudio Input Audio Output RS485/422 ConnectorFunction Pin Performance Considerations M2.12
Top Page Image Contents