Axis Communications Q1615-E user manual PTZ Controls, AMC Audio Controls

Page 15

AXIS Q1615-E Network Camera

Access the Product

The Play button connects to the Axis product and starts playing a media stream.

The Stop button stops the media stream.

The Snapshot button takes a snapshot of the video image. The location where the image is saved can be specified in the AMC Control Panel.

Click the View Full Screen button and the video image will fill the entire screen. Press ESC (Escape) on the computer keyboard to cancel full screen view.

The Record button is used to record the current video stream. The location where the recording is saved can be specified in the AMC Control Panel. Enable this button from Live View Config > Viewer Settings.

AMC Audio Controls

AMC audio buttons control the speakers and microphone connected to the client computer. The buttons are only visible when audio is enabled.

Speaker button — Click to turn the speakers on or off.

Microphone button – Click to mute or unmute the microphone. In Simplex - speaker only mode, the Microphone and Talk buttons must both be active to send audio to the Axis product. Click either button to stop audio transmission.

Use the slider to control the volume of the speakers and the microphone.

Half-duplex mode

The Talk/Listen button is used to switch between sending and receiving audio. The button can be configured from the Audio tab in the AMC Control panel:

•Push-To-Talk mode: Click and hold the button to talk/send. Release the button to listen.

•Toggle mode: Click once to switch between talking and listening.

Simplex – speaker only mode

To send audio, the Talk and Microphone buttons must both be active. Click either button to stop audio transmission.

PTZ Controls

The Live View page also displays Pan/Tilt/Zoom (PTZ) controls. The administrator can enable/disable controls for specified users under System Options > Security > Users.

Note

These controls are available if digital PTZ is enabled in the selected view area or if a PTZ driver has been uploaded. For more information on view areas, see View Area on page 27. For more information on how to upload a driver, see . To switch between the two options see .

Click the Emulate joystick mode button and click in the image to move the camera view in the direction of the mouse pointer.

Click the Center mode button and click in the image to center the camera view on that position. The center mode button could also be used to zoom in on a specific area. Click in the image and drag to draw a rectangle surrounding the area to be magnified. To zoom out, rotate the mouse wheel.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Axis Q1615-E Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q1615-E Network Camera Table of ContentsConnectors Performance Considerations Hardware Overview Axis Q1615-E Network Camera Connectors and Buttons Function button has multiple functions LED IndicatorsControl Button Function ButtonBuzzer Signal for Focus Assistant Status LED Behavior for Focus AssistantReplace the Lens Axis Q1615-E Network Camera Set the Root Password Access the ProductAccess from a Browser Access from the InternetControls on the Live View Set Power Line FrequencyConfigure Capture Mode Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerAMC Audio Controls PTZ ControlsAxis Q1615-E Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsSet Up the Product Basic SetupAdjust Focus Focus Assistant Image Video and AudioVideo Stream Pixel CounterClick Save to apply the new settings Stream Profiles264 Camera Settings Capture ModeGo to Setup Video & Audio Camera Settings White Balance View AreaImage Appearance Image CorrectionLow light priority slider toward low noise Example Exposure SettingsShutter & Gain Set Shutter toView Area Go to Video & Audio Overlay Image OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabGo to Events Action Rules Use Overlay Text in an Action RuleAudio Modes Audio SettingsPrivacy Mask FocusAudio Input Audio Output Audio ClipsBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsGuard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControls Operator Same as administrator but with lower priorityAdvanced Control QueueAxis Q1615-E Network Camera Shock Detection DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection Windows15% 60-90% 75-95% Default valuesAudio Detection Recommended valuesApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q1615-E Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesGo to Events Recipients and click Add Set Up Email RecipientsAdd Recipients Create SchedulesGo to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingClick Save to save and start the recording Languages IP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Date & Time To install a self-signed certificateGo to Setup System Options Security Certificates Click Install certificate and upload the certificateNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 Network Share StorageBonjour SD CardPorts & Devices MaintenanceLogs & Reports SupportSupport Overview System OverviewReset to Factory Default Settings Plain ConfigFile Upload Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserSetup Video & Audio Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Network Security Function/group Specifications Audio Audio streamingAudio input Audio outputWeight Function/group SpecificationsPower ConnectorsFunction Pin Specifications ConnectorsWarranty ConnectorFunction Pin RS485/422 ConnectorPerformance Considerations OutputAxis Q1615-E Network Camera M2.8
Top Page Image Contents