Axis Communications Q1615-E user manual Connectors and Buttons

Page 8

AXIS Q1615-E Network Camera

Hardware Overview

2.Bottom cover

3.Bottom cover screws (4x)

4.Bracket adjustment screw

5.Wall mount

Connectors and Buttons

For technical specifications, see page 65.

Network Connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

NOTICE

Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. All cables connecting the product to the network and that are routed outdoors or in demanding electrical environments shall be intended for their specific use. Make sure that the network devices

are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .

I/O Connector

Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to the 0 V DC reference point and power (DC output), the I/O connector provides the interface to:

•Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

•Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Note

The I/O connector is connected to the housing (fan/heater) on delivery. In the case of a fan or heater error, an input signal will be triggered in the camera. Set up an action rule in the camera to configure which action the signal shall trigger. For information about events and action rules, see Events on page 43.

Audio Connector

The Axis product has the following audio connectors:

•Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal.

•Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier . A stereo connector must be used for audio out.

RS485/RS422 Connector

Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as PTZ devices.

SD Card Slot

A microSD card (not included) can be used for local recording with removable storage. For more information, see Technical Specifications on page 65.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Axis Q1615-E Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1615-E Network CameraConnectors Performance Considerations Hardware Overview Axis Q1615-E Network Camera Connectors and Buttons LED Indicators Control ButtonFunction Button Function button has multiple functionsReplace the Lens Buzzer Signal for Focus AssistantStatus LED Behavior for Focus Assistant Axis Q1615-E Network Camera Access the Product Access from a BrowserAccess from the Internet Set the Root PasswordSet Power Line Frequency Configure Capture ModeLive View Controls on the Live ViewGo to Setup Events Axis Media Control viewer toolbarManual Trigger To show the manual trigger buttons in the Live ViewPTZ Controls AMC Audio ControlsAxis Q1615-E Network Camera Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingAdjust Focus Set Up the ProductBasic Setup Focus Assistant Video and Audio Video StreamPixel Counter Image264 Click Save to apply the new settingsStream Profiles Go to Setup Video & Audio Camera Settings Camera SettingsCapture Mode View Area Image AppearanceImage Correction White BalanceExposure Settings Shutter & GainSet Shutter to Low light priority slider toward low noise ExampleView Area Overlay Overlay ImageGo to Video & Audio Video Stream and select the Image tab Go to Video & Audio Overlay ImageUse Overlay Text in an Action Rule Go to Events Action RulesAudio Settings Privacy MaskFocus Audio ModesAudio Input Audio Clips Audio OutputConfigure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom Guard TourOperator Same as administrator but with lower priority AdvancedControl Queue ControlsAxis Q1615-E Network Camera Detectors Camera TamperingMotion Detection Shock DetectionSet Up Motion Detection Windows Motion Detection ParametersDefault values Audio DetectionRecommended values 15% 60-90% 75-95%Install Application Go to Setup ApplicationsApplications Application LicensesAxis Q1615-E Network Camera Set Up Action Rules EventsConvert Event Types to Action Rules Go to Events Action Rules and click AddSet Up Email Recipients Add RecipientsCreate Schedules Go to Events Recipients and click AddSet Up Recurrences Go to Events Recurrences and click AddRecordings Recording ListContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages System Options SecurityUsers IP Address FilterGo to System Options Security Ieee IeeeCertificates To install a self-signed certificate Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeBasic TCP/IP Settings NetworkAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM Storage BonjourSD Card Network ShareMaintenance Ports & DevicesSupport Support OverviewSystem Overview Logs & ReportsFile Upload Reset to Factory Default SettingsPlain Config Troubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsSettings Storage and disk management problemsNo audio Poor audio qualityTechnical Specifications Function/group Specifications Audio Audio streaming Audio inputAudio output Network SecurityFunction/group Specifications PowerConnectors WeightConnectors WarrantyConnector Function Pin SpecificationsRS485/422 Connector Performance ConsiderationsOutput Function PinAxis Q1615-E Network Camera M2.8
Top Page Image Contents