Axis Communications P1354-E user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 51

AXIS P1354–E Network Camera

System Options

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 54.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The Axis product supports SD cards with the following file systems:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — most SD cards are pre-formatted with vFAT when purchased.

If required, the SD card can be manually formatted to the desired file system. To format the SD card:

1.Insert the SD card in the SD card slot.

2.Go to System Options > Storage and click SD Card.

3.Click Format and select the desired file system.

Note

During formatting any previous data stored on the disk will be lost.

Mounting is done automatically when the card is inserted or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted.

To unmount the SD card:

1.Go to System Options > Storage and click SD Card.

2.Click Unmount.

51

Image 51

Contents Axis P1354-E Network Camera Equipment Modifications About this documentLiability Intellectual Property RightsLearn More SupportAxis P1354-E Network Camera Table of ContentsTechnical Specifications Hardware Overview Hardware OverviewAxis P1354-E Network Camera Connectors Color Indication LED IndicatorsStatus LED when using Focus Assistant Replacing the lensUnscrew the standard lens Attach and screw on the new lens Accessing the Product Accessing the ProductAccess from a Browser Click Create self-signed certificate Accessing the Product Access from the InternetSet the Root Password Network TCP/IP AdvancedAccessing the Product Set Power Line Frequency PTZ ModeLive View Manual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbarAMC Audio Controls PTZ ControlsAxis P1354-E Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Accessing Audio Streams Focus Setting Up the ProductSetting Up the Product Basic SetupPixel Counter Video and AudioVideo and Audio Video Stream264 ImageVideo and Audio Stream Profiles Camera SettingsSet Shutter to Iris configurationIris adjustment Shutter & GainDay/Night Image SettingsView Area OverlayGo to Video & Audio Overlay Image Audio SettingsPrivacy Mask Overlay ImageAudio Input Audio ModesAudio Output Audio ClipsLive View Config Live View ConfigDefault Viewer for Browsers Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis P1354-E Network Camera PTZ Pan Tilt Zoom Preset PositionsInstalling a PTZ driver Go to PTZ Preset PositionsControls Device SettingsGuard Tour AdvancedControl Queue Operator Same as administrator but with lower priorityMotion Detection DetectorsDetectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsRecommended values Default valuesAudio Detection Low level 0%Applications ApplicationsEvents EventsSetting Up an Action Rule PTZ ControlGo to Events Action Rules and click Add Go to Events Recipients and click Add RecipientsSchedules Recipient Use with actionGo to Events Recurrences and click Add Events RecurrencesContinuous Recording RecordingsRecordings Recording ListUsers System OptionsSystem Options SecurityCertificates Date & TimeIeee Audio SupportNetwork Basic TCP/IP SettingsIPv4 Address Configuration IPv6 Address ConfigurationAxis Video Hosting System Avhs Assign IP Address using ARP/PingLinux/Unix syntax Linux/Unix exampleAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 HttpsSmtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264COM Port Ports & DevicesNetwork Share PortsSupport MaintenanceFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P1354-E Network Camera Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallySettings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsTechnical Specifications Technical SpecificationsAudio input Function/group Specifications Audio Audio streamingBuilt-in Microphone Specification Network Security MaintenanceDimensions Function/group Specifications Installation aidsPower ConnectorsPower connector Technical Specifications ConnectorsTerminal connector Function Pin SpecificationsAudio Input Audio Output Audio connectorRS-485/422 connector Performance ConsiderationsM2.2